[ 0.000000@0]d Booting Linux on physical CPU 0x0 [ 0.000000@0]d Linux version 4.9.269 (docker@c87ab3b5f7fe) (gcc version 13.2.0 (GCC) ) #1 SMP PREEMPT Wed Feb 5 07:04:47 IST 2025 [ 0.000000@0]d Boot CPU: AArch64 Processor [412fd050] [ 0.000000@0]d CoreELEC dt-id: sc2_s905x4_sei_smb_280_id5 [ 0.000000@0]d Machine model: Dune/Homatics R 4K Plus [ 0.000000@0]d earlycon: aml-uart0 at MMIO 0x00000000fe07a000 (options '') [ 0.000000@0]d bootconsole [aml-uart0] enabled [ 0.000000@0]d 08400000 - 08500000, 1024 KB, ramoops@0x08400000 [ 0.000000@0]d __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000008400000, len:52 MiB [ 0.000000@0]d 05000000 - 08400000, 53248 KB, linux,secmon [ 0.000000@0]d __reserved_mem_alloc_size, start:0x00000000f0800000, end:0x00000000f1000000, len:8 MiB [ 0.000000@0]d f0800000 - f1000000, 8192 KB, linux,meson-fb [ 0.000000@0]d __reserved_mem_alloc_size, start:0x0000000030000000, end:0x0000000030800000, len:8 MiB [ 0.000000@0]d 30000000 - 30800000, 8192 KB, linux,dsp_fw [ 0.000000@0]d e8800000 - f0800000, 131072 KB, linux,ion-dev [ 0.000000@0]d Reserved memory: created DMA memory pool at 0x00000000e8800000, size 0 MiB [ 0.000000@0]d e8800000 - e8800000, 0 KB, linux,ppmgr [ 0.000000@0]d cd800000 - e8800000, 442368 KB, linux,codec_mm_cma [ 0.000000@0]d cd800000 - cd800000, 0 KB, linux,codec_mm_reserved [ 0.000000@0]d cb800000 - cd800000, 32768 KB, linux,vm0_cma [ 0.000000@0]d cma: Reserved 8 MiB at 0x00000000cb000000 [ 0.000000@0]d On node 0 totalpages: 987136 [ 0.000000@0]d DMA zone: 15424 pages used for memmap [ 0.000000@0]d DMA zone: 0 pages reserved [ 0.000000@0]d DMA zone: 987136 pages, LIFO batch:31 [ 0.000000@0]d psci: probing for conduit method from DT. [ 0.000000@0]d psci: PSCIv1.0 detected in firmware. [ 0.000000@0]d psci: Using standard PSCI v0.2 function IDs [ 0.000000@0]d psci: Trusted OS migration not required [ 0.000000@0]d psci: SMC Calling Convention v1.1 [ 0.000000@0]d percpu: Embedded 21 pages/cpu s47576 r8192 d30248 u86016 [ 0.000000@0]d pcpu-alloc: s47576 r8192 d30248 u86016 alloc=21*4096 [ 0.000000@0]d pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0]d Detected VIPT I-cache on CPU0 [ 0.000000@0]d Built 1 zonelists in Zone order, mobility grouping on. Total pages: 971712 [ 0.000000@0]d Kernel command line: init=/init console=ttyS0,921600 no_console_suspend earlycon=aml-uart,0xfe07a000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 loop.max_part=4 scramble_reg=0xfe02e030 scsi_mod.scan=async xhci_hcd.quirks=0x800000 loglevel=1 otg_device=1 hw_id=5 bct3236_rgbcolor=0x003028 skip_driver_register=0 cma_first_wm_low=on logo=osd0,loaded,0x00300000 vout=2160p60hz,enable panel_type=lcd_1 hdmitx=,420,10bit hdmimode=1080p60hz hdmichecksum=0x725c0000 dolby_vision_on=0 hdr_policy=1 hdr_priority= androidboot.enable_console= config_csc_en=1frac_rate_policy=1 hdmi_read_edid=1 cvbsmode=480cvbs osd_reverse=0 video_reverse=0 irq_check_en=0 androidboot.selinux=enforcing androidboot.firstboot=0 androidboot.sei_kernelLog=0 jtag=disable disable_ir=0 androidboot.bootloader=01.01.240930.103908 androidboot.hardware=amlogic mac=8C:98:06:7B:86:50 androidboot.mac=8C:98:06:7B:86:50 androidboot.serialno=GZ24110224900489 androidboot.oem=ATV00100021000000000000 [ 0.000000@0]d fb: osd0 [ 0.000000@0]d fb: loaded [ 0.000000@0]d fb: 0x00300000 [ 0.000000@0]d vout: 2160p60hz [ 0.000000@0]d vout: enable: 1 [ 0.000000@0]d lcd: panel_type: lcd_1 [ 0.000000@0]d hdmitx: get hdmi checksum: 0x725c0000 [ 0.000000@0]d get_dolby_on: 0 [ 0.000000@0]d am_vecm: boot hdr_policy: 1 [ 0.000000@0]d vpp_axis_reverse: bootargs is 0 [ 0.000000@0]d DI: di_read_canvas_reverse: bootargs is 0. [ 0.000000@0]d phlock_phase_config: bootargs is 0. [ 0.000000@0]d vout: 1080p60hz [ 0.000000@0]d vout: en: 1 [ 0.000000@0]d fb: osd0 [ 0.000000@0]d fb: loaded [ 0.000000@0]d fb: 0x00300000 [ 0.000000@0]d am_vecm: boot hdr_policy: 1 [ 0.000000@0]d PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000@0]d Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000@0]d Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000@0]d Memory: 3157920K/3948544K available (13310K kernel code, 2370K rwdata, 5768K rodata, 5888K init, 1429K bss, 106592K reserved, 684032K cma-reserved) [ 0.000000@0]d Virtual kernel memory layout: [ 0.000000@0]d modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0]d vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0]d .text : 0xffffff8009080000 - 0xffffff8009d80000 ( 13312 KB) [ 0.000000@0]d .rodata : 0xffffff8009d80000 - 0xffffff800a330000 ( 5824 KB) [ 0.000000@0]d .init : 0xffffff800a330000 - 0xffffff800a8f0000 ( 5888 KB) [ 0.000000@0]d .data : 0xffffff800a8f0000 - 0xffffff800ab40808 ( 2371 KB) [ 0.000000@0]d .bss : 0xffffff800ab40808 - 0xffffff800aca5da4 ( 1430 KB) [ 0.000000@0]d fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000@0]d PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0]d vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0]d 0xffffffbf00000000 - 0xffffffbf03c40000 ( 60 MB actual) [ 0.000000@0]d memory : 0xffffffc000000000 - 0xffffffc0f1000000 ( 3856 MB) [ 0.000000@0]d SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0]d Preemptible hierarchical RCU implementation. [ 0.000000@0]d Build-time adjustment of leaf fanout to 64. [ 0.000000@0]d RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0]d RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000@0]d NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0]d irq_meson_gpio: 87 to 12 gpio interrupt mux initialized [ 0.000000@0]d meson_sc2_sdemmc_init: register amlogic sdemmc clk [ 0.000000@0]d meson_sc2_sdemmc_init: register amlogic sdemmc clk [ 0.000000@0]d sc2_clkc_init initialization complete [ 0.000000@0]d arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0]d clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000003@0]d sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000025@0]d meson_bc_timer: mclk->mux_reg = (ptrval),mclk->reg = (ptrval) [ 0.000317@0]- Console: colour dummy device 80x25 [ 0.000322@0]- console [tty0] enabled [ 0.000324@0]- bootconsole [aml-uart0] disabled [ 0.000335@0]- Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.000340@0]- pid_max: default: 32768 minimum: 301 [ 0.000407@0]- Security Framework initialized [ 0.000414@0]- SELinux: Initializing. [ 0.000432@0]- SELinux: Starting in permissive mode [ 0.000453@0]- Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.000455@0]- Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.000912@0]- ftrace: allocating 42366 entries in 166 pages [ 0.047707@0]- sched-energy: CPU device node has no sched-energy-costs [ 0.059461@0]- ASID allocator initialised with 65536 entries [ 0.087853@0]- secmon: can't fine clear_range [ 0.089393@0]- chip version = 32:D - 2:0 [ 0.135870@1]d Detected VIPT I-cache on CPU1 [ 0.135914@1]d CPU1: Booted secondary processor [412fd050] [ 0.167904@2]d Detected VIPT I-cache on CPU2 [ 0.167938@2]d CPU2: Booted secondary processor [412fd050] [ 0.199951@3]d Detected VIPT I-cache on CPU3 [ 0.199982@3]d CPU3: Booted secondary processor [412fd050] [ 0.200042@0]- Brought up 4 CPUs [ 0.200045@0]- SMP: Total of 4 processors activated. [ 0.200048@0]- CPU features: detected feature: Privileged Access Never [ 0.200050@0]- CPU features: detected feature: User Access Override [ 0.200052@0]- CPU features: detected feature: Virtualization Host Extensions [ 0.200053@0]- CPU features: detected feature: 32-bit EL0 Support [ 0.200157@0]- CPU: All CPU(s) started at EL2 [ 0.200167@0]d alternatives: patching kernel code [ 0.201749@0]- devtmpfs: initialized [ 0.212646@0]- clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.212656@0]- futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.212767@0]- pinctrl core: initialized pinctrl subsystem [ 0.213459@0]- NET: Registered protocol family 16 [ 0.214237@2]- schedtune: init normalization constants... [ 0.214241@2]- schedtune: no energy model data [ 0.214242@2]- schedtune: disabled! [ 0.228109@2]- cpuidle: using governor menu [ 0.228164@2]- register canvas platform driver [ 0.228177@2]- register rdma platform driver [ 0.229000@2]- vdso: 2 pages (1 code @ (ptrval), 1 data @ (ptrval)) [ 0.229010@2]- hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.229725@2]- DMA: preallocated 2048 KiB pool for atomic allocations [ 0.229821@2]- clkmsr: clkmsr: driver init [ 0.229823@2]- codec_mm_module_init [ 0.229847@2]- media_configs_system_init [ 0.230157@2]- pstore: using zlib compression [ 0.230202@2]- console [pstore-1] enabled [ 0.230204@2]- pstore: Registered ramoops as persistent store backend [ 0.230206@2]- ramoops: attached 0x100000@0x8400000, ecc: 0/0 [ 0.231096@2]- meson_mhu_fifo: mhu fifo start [ 0.231119@2]- meson_mhu_fifo fe006000.mhu: no payload, only use fifo [ 0.231694@2]- meson_mhu_fifo: mbox fifo init done node:ffffffc0c5d06c10, mhuf:0x2 [ 0.231886@2]- meson_mhu_sec: mhu sec start [ 0.232169@2]- meson_mhu_sec: mbox sec init done 12051 node:ffffffc0c5d07c10, mhuf:0xa [ 0.232405@2]- aml_iomap: amlogic iomap probe done [ 0.232764@2]- vpu: driver version: v20210916(13-sc2) [ 0.232783@2]- vpu: load vpu_clk: 666666667Hz(7) [ 0.232915@2]- vpu: clktree_init [ 0.232952@2]- vpu: vpu_probe OK [ 0.235025@2]- clkmsr: msr_clk_reg0= (ptrval),msr_clk_reg2= (ptrval) [ 0.235032@2]- clkmsr: msr_ring_reg0= (ptrval) [ 0.252790@2]- audio_clocks: audio_clocks_probe done [ 0.253968@2]- aml_snd_reg_map[0], reg:fe331000, size:400 [ 0.253977@2]- aml_snd_reg_map[1], reg:fe330000, size:1000 [ 0.253982@2]- aml_snd_reg_map[2], reg:fe331400, size:400 [ 0.253987@2]- aml_snd_reg_map[3], reg:fe332000, size:1000 [ 0.253993@2]- aml_snd_reg_map[4], reg:fe002000, size:1000 [ 0.253999@2]- aml_snd_reg_map[5], reg:fe331800, size:400 [ 0.254004@2]- aml_snd_reg_map[6], reg:fe331c00, size:104 [ 0.254010@2]- aml_snd_reg_map[7], reg:fe334000, size:104 [ 0.254011@2]- amlogic auge_snd_iomap probe done [ 0.254468@2]- vclk: aml_vclk_probe OK [ 0.254681@2]- aml_vdac_config_probe: cpu_id:8, name:meson-sc2-vdac [ 0.254817@2]- aml_vdac_probe: ok [ 0.254895@2]- canvas_probe reg= (ptrval),size=2000 [ 0.254908@2]- canvas maped reg_base = (ptrval) [ 0.255964@2]- rdma_probe,cpu_type:3, ver:1, len:16,rdma_table_size:65536 [ 0.256253@2]- rdma_register, rdma_table_addr (ptrval) rdma_table_addr_phy cb200000 reg_buf (ptrval) [ 0.256255@2]- rdma_register success, handle 1 table_size 65536 [ 0.256258@2]- set_rdma_handle video rdma handle = 1. [ 0.256279@2]- classs created ok [ 0.256285@2]- classs file created ok [ 0.257929@2]- cvbs_out: cvbsout_probe, cpu_id:8,name:meson-sc2-cvbsout [ 0.257935@2]- ERROR: could not get clock /cvbsout:venci_top_gate(0) [ 0.257955@2]- cvbs_out: error: cvbsout_clktree_probe: clk venci_top_gate [ 0.257963@2]- ERROR: could not get clock /cvbsout:venci_0_gate(1) [ 0.257970@2]- cvbs_out: error: cvbsout_clktree_probe: clk venci_0_gate [ 0.257978@2]- ERROR: could not get clock /cvbsout:venci_1_gate(2) [ 0.257985@2]- cvbs_out: error: cvbsout_clktree_probe: clk venci_1_gate [ 0.257993@2]- ERROR: could not get clock /cvbsout:vdac_clk_gate(3) [ 0.258000@2]- cvbs_out: error: cvbsout_clktree_probe: clk vdac_clk_gate [ 0.258007@2]- cvbs_out: clk path:0x0 [ 0.258010@2]- cvbs_out: find performance_pal config [ 0.258015@2]- cvbs_out: register cvbs module server ok [ 0.258016@2]- cvbs_out: register cvbs module vout2 server ok [ 0.258019@2]- cvbs_out: chrdev devno 262144000 for disp [ 0.258156@2]- cvbs_out: create cdev cvbs [ 0.258158@2]- cvbs_out: cvbsout_probe OK [ 0.258486@2]- codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.258542@2]- codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.258544@2]- codec_mm_probe ok [ 0.377663@1]- SCSI subsystem initialized [ 0.377772@1]- libata version 3.00 loaded. [ 0.377941@1]- usbcore: registered new interface driver usbfs [ 0.377972@1]- usbcore: registered new interface driver hub [ 0.377995@1]- usbcore: registered new device driver usb [ 0.378073@1]- pps_core: LinuxPPS API ver. 1 registered [ 0.378075@1]- pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.378089@1]- PTP clock support registered [ 0.378450@1]- secmon: share in base: 0xffffffc0050f9000, share out base: 0xffffffc0050ff000 [ 0.378453@1]- secmon: phy_in_base: 0x50f9000, phy_out_base: 0x50ff000 [ 0.378673@1]- fb: osd_init_module [ 0.378916@1]- fb: viu vsync irq: 37 [ 0.378922@1]- fb: viu2 vsync irq: 41 [ 0.378928@1]- fb: rdma irq: 47 [ 0.379258@1]- fb: osd_rdma_init: rdma_table p=0xcb210000,op=0xcb210000 , v=0x (ptrval) [ 0.379277@1]- rdma_register, rdma_table_addr (ptrval) rdma_table_addr_phy cb211000 reg_buf (ptrval) [ 0.379279@1]- rdma_register success, handle 2 table_size 4096 [ 0.379281@1]- fb: osd_rdma_init:osd rdma handle = 2. [ 0.379291@1]- fb: mem_size: 0x800000 [ 0.379292@1]- fb: mem_size: 0x4b80000 [ 0.379293@1]- fb: mem_size: 0x100000 [ 0.379294@1]- fb: mem_size: 0x100000 [ 0.379295@1]- fb: mem_size: 0x800000 [ 0.379365@1]- meson-fb fb: assigned reserved memory node linux,meson-fb [ 0.379368@1]- fb: reserved memory base:0x00000000f0800000, size:800000 [ 0.379497@1]- fb: init fbdev bpp is:32 [ 0.380259@3]- fb: set osd0 reverse as NONE [ 0.388318@3]- fb: osd probe OK [ 0.388825@3]- hdmitx: system: Ver: 20210902 [ 0.388850@3]- hdmitx: system: no hdmitx_i2c of pinctrl state [ 0.388959@3]- hdmitx: system: hpd irq = 36, viu1_vsync = 37 [ 0.388963@3]- ERROR: could not get clock /amhdmitx:hdmi_vapb_clk(3) [ 0.388986@3]- ERROR: could not get clock /amhdmitx:hdmi_vpu_clk(4) [ 0.388996@3]- ERROR: could not get clock /amhdmitx:venci_top_gate(0) [ 0.389005@3]- ERROR: could not get clock /amhdmitx:venci_0_gate(1) [ 0.389013@3]- ERROR: could not get clock /amhdmitx:venci_1_gate(2) [ 0.389323@3]- hdmitx: hw: avmute set to 1 [ 0.389379@3]- hdmitx: hdmitx_uboot_audio_en[604] data = 0x1f [ 0.390278@3]- vout sys: aml_vs_probe OK [ 0.390715@3]- hdmitx: hdmitx_set_current_vmode[5644] [ 0.390719@3]- hdmitx: system: recalc before 1080p60hz 60 1, frac 0 [ 0.390721@3]- hdmitx: system: recalc after 1080p60hz 60 1, frac 0 [ 0.390722@3]- hdmitx: alread display in uboot [ 0.390733@3]- hdmitx: system: update rx hdr info 0 [ 0.390735@3]- vout: init mode 1080p60hz set ok [ 0.390737@3]- fb: current vmode=1080p60hz, cmd: 0x60000 [ 0.390741@3]- vout sys: update date: 0x003c0001 [ 0.390742@3]- vout: aml_vout_probe OK [ 0.390989@3]- chip type:0x32 [ 0.391025@3]- can't find sec_base, set bytes_per_cycle to 16 [ 0.391293@3]- Advanced Linux Sound Architecture Driver Initialized. [ 0.391924@3]- NetLabel: Initializing [ 0.391927@3]- NetLabel: domain hash size = 128 [ 0.391929@3]- NetLabel: protocols = UNLABELED CIPSOv4 [ 0.391957@3]- NetLabel: unlabeled traffic allowed by default [ 0.392924@3]- clocksource: Switched to clocksource arch_sys_counter [ 0.425012@3]- VFS: Disk quotas dquot_6.6.0 [ 0.425061@3]- VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.425122@3]- FS-Cache: Loaded [ 0.431421@2]- NET: Registered protocol family 2 [ 0.453023@2]- TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.453133@2]- TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.453478@2]- TCP: Hash tables configured (established 32768 bind 32768) [ 0.453539@2]- UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.453571@2]- UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.453725@2]- NET: Registered protocol family 1 [ 0.453996@2]- RPC: Registered named UNIX socket transport module. [ 0.453998@2]- RPC: Registered udp transport module. [ 0.454000@2]- RPC: Registered tcp transport module. [ 0.454001@2]- RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.454008@2]- PCI: CLS 0 bytes, default 64 [ 0.455242@2]- Wifi: bcmdhd_init_wlan_mem: [dhd] STATIC-MSG) bcmdhd_init_wlan_mem : 101.10.361.10 (wlan=r892223-20210623-1) [ 0.455576@2]- Wifi: bcmdhd_init_wlan_mem: [dhd] STATIC-MSG) bcmdhd_init_wlan_mem : prealloc ok: 8162304(7971K) [ 0.456371@2]- Unpacking initramfs... [ 0.471925@2]- Freeing initrd memory: 6112K [ 0.472750@2]- unifykey: normal key used! [ 0.473095@2]- unifykey: no efuse-version set, use default value: -1 [ 0.473341@2]- unifykey: aml_unifykeys_init done! [ 0.474177@2]- hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.475663@0]- audit: initializing netlink subsys (disabled) [ 0.475702@0]- audit: type=2000 audit(0.440:1): initialized [ 0.476206@0]- workingset: timestamp_bits=45 max_order=20 bucket_order=0 [ 0.481074@0]- squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.481460@0]- FS-Cache: Netfs 'nfs' registered for caching [ 0.481835@0]- NFS: Registering the id_resolver key type [ 0.481854@0]- Key type id_resolver registered [ 0.481855@0]- Key type id_legacy registered [ 0.481862@0]- nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.481864@0]- nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.482003@0]- FS-Cache: Netfs 'cifs' registered for caching [ 0.482487@0]- SELinux: Registering netfilter hooks [ 0.484838@2]- NET: Registered protocol family 38 [ 0.484848@2]- Key type asymmetric registered [ 0.484850@2]- Asymmetric key parser 'x509' registered [ 0.485026@2]- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.485031@2]- io scheduler noop registered (default) [ 0.485033@2]- io scheduler deadline registered [ 0.485119@2]- io scheduler cfq registered [ 0.487007@3]d random: fast init done [ 0.487040@3]- random: crng init done [ 0.487064@2]- [drm] Initialized [ 0.487133@2]- Unable to detect cache hierarchy for CPU 0 [ 0.490022@2]- loop: module loaded [ 0.490889@2]- mtdoops: mtd device (mtddev=name/number) must be supplied [ 0.491326@2]- libphy: Fixed MDIO Bus: probed [ 0.492300@2]- Miss mc_val for REG0 [ 0.492306@2]- auto_cali_idx 1 [ 0.492725@2]- meson6-dwmac fdc00000.ethernet: no reset control found [ 0.492730@2]- stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 0.492731@2]- Ring mode enabled [ 0.492733@2]- DMA HW capability register supported [ 0.492735@2]- Normal descriptors [ 0.492737@2]- RX Checksum Offload Engine supported [ 0.492738@2]- COE Type 2 [ 0.492739@2]- TX Checksum insertion supported [ 0.492740@2]- Wake-Up On Lan supported [ 0.492764@2]- Enable RX Mitigation via HW Watchdog Timer [ 0.492905@2]- libphy: yzhang..read phyaddr=0, phyid=4f51e91b [ 0.492908@2]- libphy: yzhang..get YT8511, abt to set 125m clk out, phyaddr=0, phyid=4f51e91b [ 0.507939@0]d hdmitx: edid: EDID Parser: [ 0.507960@0]d hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 0.507963@0]d hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=2 [ 0.507965@0]d hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 0.507966@0]d hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=2 [ 0.507986@0]d hdmitx: edid: get dtd0 vic: 97 [ 0.507988@0]d hdmitx: edid: get dtd1 vic: 16 [ 0.507990@0]d hdmitx: hdmitx: get PMT vic: 97 [ 0.507992@0]d hdmitx: edid: find IEEEOUT [ 0.508003@0]- hdmitx: edid: blk0 raw data [ 0.508022@0]- hdmitx: edid: [ 0.508022@0]- 00ffffffffffff0011ee660001010101001d010380a05a780aee91a3544c9926 [ 0.508022@0]- 0f5054a1080031404540614071408180d1c00101010108e80030f2705a80b058 [ 0.508022@0]- 8a0040846300001e023a801871382d40582c4500c48e2100001e000000fc0044 [ 0.508022@0]- 454e4f4e2d4156520a202020000000fd0018781eff77000a2020202020200172 [ 0.508022@0]- [ 0.508022@0]- [ 0.508024@0]- hdmitx: edid: blk1 raw data [ 0.508042@0]- hdmitx: edid: [ 0.508042@0]- 02037af15f61606665101f04130514030212202122155d5e5f6263643f400e23 [ 0.508042@0]- 0f241e26380f7f073d1ec01507505f7e03570603677e034d02005f7e01835f00 [ 0.508042@0]- 006e030c002500b83c2c00800102030468d85dc40178800b02e20f0fe3060d01 [ 0.508042@0]- eb0146d00048229e7e626597e305c000e200cfe61146d000700000000000005c [ 0.508042@0]- [ 0.508042@0]- [ 0.508046@0]- hdmitx: system: update rx hdr info d [ 0.508222@0]- hdmitx: hdmitx: get vic 353 cscd [ 0.508227@0]- hdmitx: hdmitx: mode name 3840x2160p60hz420 [ 0.508234@0]- hdmitx: hdmitx: tmds clock 594 [ 0.508235@0]- hdmitx: hdmitx: act clock: 297 [ 0.508242@0]h hdmitx: system: irq 80000002 0 [ 0.593637@2]- yt8511_config_out_125m, phy clk out, val=0x008006 [ 0.593681@2]- libphy: yzhang..8511 set 125m clk out, reg=0x8006 [ 0.594491@2]- libphy: yzhang..read phyaddr=7, phyid=4f51e91b [ 0.594494@2]- libphy: yzhang..get YT8511, abt to set 125m clk out, phyaddr=7, phyid=4f51e91b [ 0.694978@2]- yt8511_config_out_125m, phy clk out, val=0x008006 [ 0.695020@2]- libphy: yzhang..8511 set 125m clk out, reg=0x8006 [ 0.697092@2]- libphy: stmmac: probed [ 0.697097@2]- eth%d: PHY ID 4f51e91b at 0 IRQ POLL (stmmac-0:00) active [ 0.697099@2]- eth%d: PHY ID 4f51e91b at 7 IRQ POLL (stmmac-0:07) [ 0.698275@2]- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.698299@2]- ehci-pci: EHCI PCI platform driver [ 0.698335@2]- ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.698342@2]- ohci-pci: OHCI PCI platform driver [ 0.698613@2]- usbcore: registered new interface driver cdc_acm [ 0.698615@2]- cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 0.698653@2]- usbcore: registered new interface driver usb-storage [ 0.698711@2]- usbcore: registered new interface driver usbserial [ 0.698732@2]- usbcore: registered new interface driver usbserial_generic [ 0.698752@2]- usbserial: USB Serial support registered for generic [ 0.699053@2]- mousedev: PS/2 mouse device common for all mice [ 0.699262@2]- i2c /dev entries driver [ 0.700352@2]- ledtrig-cpu: registered to indicate activity on CPUs [ 0.700571@2]- hidraw: raw HID events driver (C) Jiri Kosina [ 0.700786@2]- usbcore: registered new interface driver usbhid [ 0.700788@2]- usbhid: USB HID core driver [ 0.701337@2]- value of voltage_tolerance 0 [ 0.701341@2]- meson_cpufreq_init:don't find the node [ 0.701360@2]- value of gp1_clk_target 0 [ 0.701971@2]- cpu cpu0: meson_cpufreq_init: CPU 0 initialized [ 0.701993@2]- cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1992000 KHz [ 0.703117@2]- cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 2000000 KHz [ 0.703632@2]- fe07a000.serial: clock gate not found [ 0.703681@2]- meson_uart fe07a000.serial: ==uart0 reg addr = 0000000049d1007d [ 0.703709@2]- fe07a000.serial: ttyS0 at MMIO 0xfe07a000 (irq = 23, base_baud = 1500000) is a meson_uart [ 0.703719@2]- meson_uart fe07a000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 921600 [ 0.727047@2]- console [ttyS0] enabled [ 0.727492@2]- meson_uart fe080000.serial: ==uart1 reg addr = 00000000d1813a75 [ 0.727520@2]- fe080000.serial: ttyS1 at MMIO 0xfe080000 (irq = 35, base_baud = 1500000) is a meson_uart [ 0.728381@2]- amlogic-new-usb2-v2 fe03a000.usb2phy: USB2 phy probe:phy_mem:0xfe03a000, iomap phy_base:0xffffff80084c5000 [ 0.728591@2]- amlogic-new-usb3-v2 fe03a080.usb3phy: USB3 phy probe:phy_mem:0xfe03a080, iomap phy_base:0xffffff80084cd080 [ 0.730602@2]- aml_dma fe440400.aml_dma: Aml dma [ 0.731892@2]- aml_aes_dma fe440400.aml_dma:aml_aes: Aml AES_dma [ 0.732517@2]- aml_tdes_dma fe440400.aml_dma:aml_tdes: Aml TDES_dma [ 0.732852@2]- aml_sha_dma fe440400.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma [ 0.733186@2]- aml_crypto_dev fe440400.aml_dma:crypto: Aml crypto device [ 0.733375@2]- gpio-keypad gpio_keypad: bluetooth key(600) registed. [ 0.733468@2]- input: gpio_keypad as /devices/platform/gpio_keypad/input/input0 [ 0.733755@2]- Enable disable_nonboot_cpus in syscore shutdown. [ 0.735016@2]- ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev [ 0.735033@2]- ion-dev: failed get fb memory [ 0.735042@2]- ion-dev: failed get secure memory [ 0.735211@2]- ion-dev: add heap type:0 id:0 [ 0.735282@2]- ion-dev: add heap type:5 id:5 [ 0.735324@2]- ion-dev: add heap type:4 id:4 [ 0.735326@2]- ion-dev: dev_ion_probe, create 3 heaps [ 0.735484@2]- ge2d: ge2d_init_module [ 0.737367@2]- ge2d: ge2d clock is 499 MHZ [ 0.737390@2]- ge2d: reserved mem is not used [ 0.737423@2]- ge2d: ge2d start monitor [ 0.737868@2]- new arch is :1. [ 0.737936@2]- [tsync_pcr_init]init success. [ 0.738165@2]- warning: film grain not support! [ 0.738166@2]- warning: film grain not support! [ 0.738190@2]- amvideom vsync irq: 37, cpu_type:3 [ 0.738195@2]- amvideom vsync viu2 irq: 41 [ 0.738216@2]- create_ge2d_work_queue video task ok [ 0.738713@2]- create_video_receiver video_render.0 00000000b2005722, path_id:2 success [ 0.738716@2]- create_video_receiver video_render.1 00000000d5f7d6cd, path_id:3 success [ 0.739021@2]- amvideocap_probe,amvideocap [ 0.739051@2]- use cma buf. [ 0.739319@2]- hdmitx: hdcp: hdmitx_hdcp_init [ 0.739824@2]- DI: di_module_init ok. [ 0.739977@2]- dim:dim_module_init [ 0.740309@2]- dim:dim_probe: [ 0.740611@2]- dev_vframe_init finish [ 0.741197@2]- dim:match name: dim_sc2:id[37] [ 0.741290@2]- dim:no reserved mem. [ 0.741318@2]- dim:pre_irq:57 [ 0.741323@2]- dim:post_irq:58 [ 0.741326@2]- dim:no aisr_irq [ 0.741365@2]- DI: vpu clkb <334000000, 667000000> [ 0.741377@2]- dim:vpu clkb =666666656. [ 0.741489@2]- dim:afbc_prob:ver[5],_sc2,mode[2] [ 0.741491@2]- dim:init ops:37:l1_sc2 [ 0.741502@2]- dim:cvs inp:0xdf~0xe0~0xe1. [ 0.741552@2]- dim:hw_init_v3: [ 0.741554@2]- dim: 0x17c5:0x1 [ 0.741555@2]- dim: 0x17c6:0x1 [ 0.741557@2]- dim: 0x1730:0xc3fe0000 [ 0.741645@2]- . [ 0.741712@2]- . [ 0.741791@2]- dim:dim_probe:ok [ 0.741910@2]- dim:dim_module_init finish [ 0.741912@2]- dil:dil_init. [ 0.742104@2]- dil:dil_init ok. [ 0.742312@2]- Reserved memory: failed to init DMA memory pool at 0x00000000e8800000, size 0 MiB [ 0.742742@2]- PPMGRDRV: info: ppmgr_dev major:506 [ 0.742955@2]- aml_vecm_init:module init [ 0.743150@2]- VECM probe start [ 0.743343@2]- Can't find tv_mode. [ 0.743346@2]- Can't find lut3d_en. [ 0.743350@2]- Can't find blue stretch en. [ 0.743363@2]- aml_iomap: write cbus reg f2 error -1 [ 0.743421@2]- vlock clk not cfg [ 0.743750@2]- aml_iomap: read cbus reg 20 error -1 [ 0.744356@2]- aml_iomap: read cbus reg 21 error -1 [ 0.756940@2]- aml_iomap: read cbus reg d1 error -1 [ 0.756972@2]- aml_iomap: write cbus reg d1 error -1 [ 0.757478@2]- aml_iomap: read cbus reg d1 error -1 [ 0.758085@2]- aml_iomap: write cbus reg d1 error -1 [ 0.758705@2]- vlock_status_init vlock_en:1 [ 0.758831@2]- aml_vecm_probe: ok [ 0.758893@2]- amdolby_vision_init:module init [ 0.759183@2]- [ 0.759183@2]- amdolby_vision probe start & ver: 20181220 [ 0.759188@2]- [ 0.759188@2]- cpu_id=5 tvmode=0 [ 0.759343@2]- dolby_vision_init_receiver(dvel) [ 0.759349@2]- dolby_vision_init_receiver: dvel [ 0.759627@2]- amdolby_vision_probe: ok [ 0.759636@2]- g12 dovi disable in uboot [ 0.760223@2]- meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 0.761731@0]h hdmitx: hdmitx_set_drm_pkt: tf=1, cf=1, colormetry=0 [ 0.800936@2]- meson-mmc: meson_mmc_probe() : success! [ 0.808764@2]- meson-mmc: gpio_cd = 1c1 [ 0.844944@2]- meson-mmc: meson_mmc_probe() : success! [ 0.884934@2]- meson-mmc: meson_mmc_probe() : success! [ 0.886476@2]- input: cec_input as /devices/virtual/input/input1 [ 0.886585@2]- get B default state [ 0.886621@2]- cectx fe044000.aocec: not find 'arc_port_mask' [ 0.901545@2]- cectx fe044000.aocec: wakeup_reason:0x0 [ 0.912506@2]- meson-mmc: emmc: clk 199999997 tuning start [ 0.916222@2]- meson-mmc: emmc: adj_win: < 0 2 3 4 > [ 0.916227@2]- meson-mmc: step:4, delay1:0x4104104, delay2:0x4004104 [ 0.920603@2]- meson-mmc: emmc: adj_win: < 0 2 3 4 > [ 0.920607@2]- meson-mmc: step:8, delay1:0x8208208, delay2:0x8008208 [ 0.925236@2]- meson-mmc: emmc: adj_win: < 0 1 2 3 4 > [ 0.925239@2]- meson-mmc: step:12, delay1:0xc30c30c, delay2:0xc00c30c [ 0.928764@2]- meson-mmc: emmc: adj_win: < 0 1 3 4 > [ 0.928768@2]- meson-mmc: left:3, right:0, mid:4, size:4 [ 0.928771@2]- meson-mmc: step:0, delay1:0x0, delay2:0x0 [ 0.928773@2]- meson-mmc: emmc: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x42000 [ 0.928851@2]- emmc: new HS200 MMC card at address 0001 [ 0.928854@2]- emmc: clock 199999997, 8-bit-bus-width [ 0.928854@2]- [ 0.929207@2]- mmcblk0: emmc:0001 A3A551 28.9 GiB [ 0.929328@2]- mmcblk0boot0: emmc:0001 A3A551 partition 1 4.00 MiB [ 0.929450@2]- mmcblk0boot1: emmc:0001 A3A551 partition 2 4.00 MiB [ 0.929553@2]- mmcblk0rpmb: emmc:0001 A3A551 partition 3 16.0 MiB [ 0.930450@2]- meson-mmc: Enter aml_emmc_partition_ops [ 0.932044@2]- meson-mmc: [mmc_read_partition_tbl] mmc read partition OK! [ 0.932045@2]- meson-mmc: add_emmc_partition [ 0.933687@2]- card key: card_blk_probe. [ 0.933695@2]- emmc_key_init:493 emmc key lba_start:0x12020,lba_end:0x12422 [ 0.935615@2]- calc c11c300e2d, store c11c300e2d [ 0.937432@2]- calc c11c300e2d, store c11c300e2d [ 0.937435@2]- do nothing [ 0.937441@2]- emmc key: emmc_key_init:519 ok. [ 0.937443@2]- meson-mmc: amlmmc_dtb_init: register dtb chardev [ 0.940941@2]- meson-mmc: total valid 2 [ 0.941115@2]- meson-mmc: amlmmc_dtb_init: register dtb chardev OK [ 0.941119@2]- meson-mmc: amlmmc_ddr_init: register ddr_parameter chardev [ 0.941213@2]- meson-mmc: amlmmc_ddr_init: register ddr parameter chardev OK [ 0.941235@2]- meson-mmc: Exit aml_emmc_partition_ops OK. [ 0.942556@2]- cectx fe044000.aocec: wakeup_data: 0x0 0x0 [ 0.943020@2]- meson ts init [ 0.943091@2]- tsensor id: 0 [ 0.943223@2]- r1p1_tsensor_read valid cnt is 0 [ 0.943237@2]- tsensor trim info: 0xfa008068! [ 0.943239@2]- tsensor hireboot: 0xc0ff2a00 [ 0.943298@2]- meson ts init [ 0.943312@2]- tsensor id: 1 [ 0.943370@2]- r1p1_tsensor_read valid cnt is 0 [ 0.943377@2]- tsensor trim info: 0xfa00006a! [ 0.943378@2]- tsensor hireboot: 0xc0ff2990 [ 0.943474@2]- audio_dsp: [dsp]register dsp to char divece(257) [ 0.943576@2]- amaudio: amaudio: driver amaudio init! [ 0.943788@2]- amaudio: amaudio_init - amaudio: driver amaudio succuess! [ 0.944363@2]- sysled: module init [ 0.944486@2]- bct3236_i2c_probe: loading driver [ 0.948376@2]- meson_wdt fe002100.watchdog: start watchdog [ 0.948380@2]- meson_wdt fe002100.watchdog: create hrtimer for watch dog [ 0.948552@2]- meson_wdt fe002100.watchdog: AML Watchdog Timer probed done [ 0.949138@2]- not get gpio_en [ 0.949142@2]- not get gpio_btwakeup [ 0.949247@2]- request_irq error ret=-22 [ 0.949305@2]- dev_pm_set_wake_irq failed: -22 [ 0.949688@2]- input: input_btrcu as /devices/platform/bt-dev/input/input2 [ 0.950173@2]- meson-saradc fe026000.saradc: set delay per tick to <1ms> by default. [ 0.950177@2]- meson-saradc fe026000.saradc: set ticks per period to <1> by default. [ 0.950900@2]- dmc_monitor_probe [ 0.951972@2]- aml_aucpu aucpu: Direct firmware load for aucpu_fw.bin failed with error -2 [ 0.951977@2]- load aucpu_fw.bin fail [ 0.951978@2]- load start_aucpu_fw fail [ 0.952208@2]- socdata fe010000.soc_info: socdata_devno:1f000000 [ 0.952461@2]- bl301_manager: driver init [ 0.952732@2]- usbcore: registered new interface driver snd-usb-audio [ 0.953647@2]- aml_codec_T9015 fe01a000.t9015: aml_T9015_audio_codec_probe [ 0.953667@2]- T9015 acodec used by auge, tdmout:1 [ 0.955164@2]- asoc debug: aml_audio_controller_probe-129 [ 0.955638@2]- aml_tdm_platform_probe, tdm ID = 1, lane_cnt = 4 [ 0.955648@2]- TDM id 1 samesource_sel:3 [ 0.955657@2]- snd_tdm fe330000.audiobus:tdm@1: lane_mask_out = 1, lane_oe_mask_out = 0 [ 0.955829@2]- TDM id 1 output clk enable:1 [ 0.955848@2]- No channel mask node Channel_Mask [ 0.955862@2]- TDM id 1 tuning clk enable:1 [ 0.955906@2]- aml_tdm_platform_probe, tdm ID = 2, lane_cnt = 4 [ 0.955917@2]- TDM id 2 i2s2hdmi:1 [ 0.955923@2]- snd_tdm fe330000.audiobus:i2s2hdmi: lane_mask_out = f, lane_oe_mask_out = 0 [ 0.955970@2]- snd_tdm fe330000.audiobus:i2s2hdmi: neither mclk_pad nor mclk2pad set [ 0.955976@2]- snd_tdm fe330000.audiobus:i2s2hdmi: aml_tdm_get_pins error! [ 0.955978@2]- No channel mask node Channel_Mask [ 0.956421@2]- aml_spdif_platform_probe, spdif ID = 0 [ 0.956770@2]- Spdif id 0 tuning clk enable:1 [ 0.956809@2]- aml_spdif_platform_probe, spdif ID = 1 [ 0.956823@2]- snd_spdif fe330000.audiobus:spdif@1: spdif 1 has no pinctrl! [ 0.957512@2]- audio-ddr-manager fe330000.audiobus:ddr_manager: 0, irqs toddr 24, frddr 28 [ 0.957524@2]- audio-ddr-manager fe330000.audiobus:ddr_manager: 1, irqs toddr 25, frddr 29 [ 0.957535@2]- audio-ddr-manager fe330000.audiobus:ddr_manager: 2, irqs toddr 26, frddr 30 [ 0.957546@2]- audio-ddr-manager fe330000.audiobus:ddr_manager: 3, irqs toddr 27, frddr 31 [ 0.957792@2]- datain_src:4, datain_chnum:2, datain_chumask:3 [ 0.957794@2]- datalb_src:1, datalb_chnum:2, datalb_chmask:3 [ 0.957795@2]- datain_lane_mask:0x1, datalb_lane_mask:0x1 [ 0.957797@2]- datalb_format: 1, chmask for lanes: 0x3 [ 0.958058@2]- loopback_platform_probe, p_loopback->id:0 register soc platform [ 0.958318@2]- audiolocker_platform_probe [ 0.958322@2]- ERROR: could not get clock /locker:lock_in(1) [ 0.958365@2]- audiolocker locker: Can't retrieve lock_in clock [ 0.959091@2]- audiolocker: probe of locker failed with error -2 [ 0.959383@2]- effect_platform_probe, line:607 [ 0.959525@2]- eqdrc_clk_set, src pll:399999993, clk:199999997 [ 0.959529@2]- effect_platform_probe module:1, lane_mask:1, ch_mask:3 [ 0.960014@2]- vad_platform_probe, failed to get vad wakeup sample rate [ 0.960158@2]- vad_platform_probe, vad wakeup sample rate = 16000 [ 0.960303@2]- vad_platform_probe vad data source sel:4, level:1 [ 0.960407@2]- input: vad_keypad as /devices/platform/soc/fe330000.audiobus/fe330000.audiobus:vad/input/input3 [ 0.960747@2]- Register vad [ 0.961000@2]- asoc-aml-card auge_sound: link 0: [ 0.961094@2]- asoc-aml-card auge_sound: name : SPDIF-B-SPDIF-B [ 0.961097@2]- asoc-aml-card auge_sound: format : 4000 [ 0.961100@2]- asoc-aml-card auge_sound: cpu : SPDIF-B / 6144000 [ 0.961102@2]- asoc-aml-card auge_sound: codec : SPDIF-B / 0 [ 0.961104@2]- asoc-aml-card auge_sound: link 1: [ 0.961199@2]- asoc-aml-card auge_sound: name : TDM-B-T9015-audio-hifi [ 0.961201@2]- asoc-aml-card auge_sound: format : 4001 [ 0.961203@2]- asoc-aml-card auge_sound: cpu : TDM-B / 12288000 [ 0.961205@2]- asoc-aml-card auge_sound: codec : T9015-audio-hifi / 0 [ 0.961207@2]- asoc-aml-card auge_sound: link 2: [ 0.961244@2]- asoc-aml-card auge_sound: name : SPDIF-A-SPDIF-A [ 0.961247@2]- asoc-aml-card auge_sound: format : 4000 [ 0.961249@2]- asoc-aml-card auge_sound: cpu : SPDIF-A / 6144000 [ 0.961251@2]- asoc-aml-card auge_sound: codec : SPDIF-A / 0 [ 0.961253@2]- asoc-aml-card auge_sound: link 3: [ 0.961315@2]- asoc-aml-card auge_sound: name : TDM-C-dummy [ 0.961317@2]- asoc-aml-card auge_sound: format : 4001 [ 0.961319@2]- asoc-aml-card auge_sound: cpu : TDM-C / 12288000 [ 0.961321@2]- asoc-aml-card auge_sound: codec : dummy / 0 [ 0.961475@2]- call standard reset interface [ 1.021123@0]- hdmitx: system: plugin [ 1.048978@2]- meson-mmc: card IN [ 1.049014@2]- meson-mmc: normal card in [ 1.154433@0]d hdmitx: edid: EDID Parser: [ 1.154450@0]d hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 1.154454@0]d hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=2 [ 1.154455@0]d hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 1.154457@0]d hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=2 [ 1.154475@0]d hdmitx: edid: get dtd0 vic: 97 [ 1.154477@0]d hdmitx: edid: get dtd1 vic: 16 [ 1.154479@0]d hdmitx: hdmitx: get PMT vic: 97 [ 1.154481@0]d hdmitx: edid: find IEEEOUT [ 1.154493@0]- hdmitx: edid: blk0 raw data [ 1.154511@0]- hdmitx: edid: [ 1.154511@0]- 00ffffffffffff0011ee660001010101001d010380a05a780aee91a3544c9926 [ 1.154511@0]- 0f5054a1080031404540614071408180d1c00101010108e80030f2705a80b058 [ 1.154511@0]- 8a0040846300001e023a801871382d40582c4500c48e2100001e000000fc0044 [ 1.154511@0]- 454e4f4e2d4156520a202020000000fd0018781eff77000a2020202020200172 [ 1.154511@0]- [ 1.154511@0]- [ 1.154513@0]- hdmitx: edid: blk1 raw data [ 1.154531@0]- hdmitx: edid: [ 1.154531@0]- 02037af15f61606665101f04130514030212202122155d5e5f6263643f400e23 [ 1.154531@0]- 0f241e26380f7f073d1ec01507505f7e03570603677e034d02005f7e01835f00 [ 1.154531@0]- 006e030c002500b83c2c00800102030468d85dc40178800b02e20f0fe3060d01 [ 1.154531@0]- eb0146d00048229e7e626597e305c000e200cfe61146d000700000000000005c [ 1.154531@0]- [ 1.154531@0]- [ 1.154533@0]- hdmitx: system: update physical size: 1600 900 [ 1.154537@0]- hdmitx: system: get current mode: 1080p60hz [ 1.154538@0]- hdmitx: system: update physical size: 1600 900 [ 1.154553@0]- hdmitx: hdmitx: display colourdepth is auto set to 12 bits (VIC: 16) [ 1.154569@0]- hdmitx: video: already init VIC = 0 Now VIC = 16 [ 1.154572@0]- hdmitx: hw: div40: 0 [ 1.168957@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Left DAC [ 1.169286@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Left DAC -> LOLP_SEL_DACL -> Lineout left P switch [ 1.170672@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Left DAC [ 1.171679@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Left DAC -> LOLP_SEL_DACL_INV -> Lineout left P switch [ 1.173344@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Left DAC [ 1.174117@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Left DAC -> LOLN_SEL_DACL_INV -> Lineout left N switch [ 1.175547@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Left DAC [ 1.176554@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Left DAC -> LOLN_SEL_DACL -> Lineout left N switch [ 1.177954@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Right DAC [ 1.178959@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Right DAC -> LORP_SEL_DACR -> Lineout right P switch [ 1.180368@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Right DAC [ 1.181394@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Right DAC -> LORP_SEL_DACR_INV -> Lineout right P switch [ 1.182838@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Right DAC [ 1.183856@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Right DAC -> LORN_SEL_DACR_INV -> Lineout right N switch [ 1.185314@2]- aml_codec_T9015 fe01a000.t9015: ASoC: no source widget found for Right DAC [ 1.186326@2]- aml_codec_T9015 fe01a000.t9015: ASoC: Failed to add route Right DAC -> LORN_SEL_DACR -> Lineout right N switch [ 1.186928@0]- hdmitx: frac_rate = 0 [ 1.186933@0]- hdmitx: config HPLL = 4455000 frac_rate = 0 [ 1.187005@0]- hdmitx: HPLL: 0xdb0004b9 [ 1.187006@0]- hdmitx: config HPLL done [ 1.187010@0]- hdmitx: set_hpll_od3_clk_div[687] div = 10 [ 1.187014@0]- hdmitx: j = 4 vid_clk_div = 1 [ 1.187026@0]- hdmitx: set enc for VIC: 16 [ 1.187889@2]- asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present [ 1.188711@2]- snd_tdm fe330000.audiobus:i2s2hdmi: ASoC: Failed to add I2SIn CLK: -16 [ 1.189708@2]- aml_dai_tdm_probe, failed add snd tdm controls [ 1.190485@2]- aml_spdif_new spdif_b, clk continuous:1 [ 1.190488@2]- spdifout_play_with_zerodata_free, spdif id:1 [ 1.190495@2]- asoc-aml-card auge_sound: SPDIF-B <-> SPDIF-B mapping ok [ 1.190499@2]- aml_dai_set_tdm_slot(), txmask(0x3), rxmask(0x3) [ 1.190501@2]- lanes_out_cnt(1), lanes_in_cnt(1) [ 1.190503@2]- lanes_lb_cnt(0) [ 1.190504@2]- slots(2), slot_width(32) [ 1.190507@2]- lanes_oe_out_cnt(0), lanes_oe_in_cnt(0) [ 1.190517@2]- asoc aml_dai_set_tdm_fmt, 0x4001, 00000000fc962dfb, id(1), clksel(1) [ 1.190522@2]- master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 1.190596@2]- asoc-aml-card auge_sound: T9015-audio-hifi <-> TDM-B mapping ok [ 1.190646@2]- aml_spdif_new spdif_a, clk continuous:1 [ 1.190648@2]- spdifout_play_with_zerodata_free, spdif id:0 [ 1.190655@2]- audio_ddr_mngr: frddr stop success, fifo id 0, regbase:0x70, arb sts:0x40000010 [ 1.190659@2]- asoc-aml-card auge_sound: SPDIF-A <-> SPDIF-A mapping ok [ 1.190662@2]- aml_dai_set_tdm_slot(), txmask(0x3), rxmask(0x3) [ 1.190664@2]- lanes_out_cnt(4), lanes_in_cnt(0) [ 1.190665@2]- lanes_lb_cnt(0) [ 1.190666@2]- slots(2), slot_width(32) [ 1.190668@2]- lanes_oe_out_cnt(0), lanes_oe_in_cnt(0) [ 1.190672@2]- asoc aml_dai_set_tdm_fmt, 0x4001, 0000000033d5650e, id(2), clksel(2) [ 1.190675@2]- master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 1.190736@2]- asoc-aml-card auge_sound: dummy <-> TDM-C mapping ok [ 1.190777@2]- aml_codec_T9015 fe01a000.t9015: ASoC: mux Lineout left P switch has no paths [ 1.191443@2]- aml_codec_T9015 fe01a000.t9015: ASoC: mux Lineout left N switch has no paths [ 1.192483@2]- aml_codec_T9015 fe01a000.t9015: ASoC: mux Lineout right P switch has no paths [ 1.196164@2]- aml_codec_T9015 fe01a000.t9015: ASoC: mux Lineout right N switch has no paths [ 1.199577@0]h meson-mmc: sd: resp_timeout,vstat:0xa1ff2800,virqc:3fff [ 1.199712@0]h meson-mmc: sd: err: wait for irq service, bus_fsm:0x8 [ 1.200514@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:8 [ 1.200517@3]- meson-mmc: meson_mmc_irq_thread_v3() 686: set 1st retry! [ 1.200569@2]- snd_card_add_kcontrols card:0000000080bebf81 [ 1.200620@2]- eq/drc v1 function enable [ 1.200624@2]- no node audio_effect for eq/drc info! [ 1.200625@2]- Failed to add audio effects v1 controls [ 1.200840@2]- Initializing XFRM netlink socket [ 1.200848@2]- IPsec XFRM device driver [ 1.201168@2]- NET: Registered protocol family 10 [ 1.201848@2]- NET: Registered protocol family 17 [ 1.201895@2]- Key type dns_resolver registered [ 1.202356@0]h meson-mmc: sd: resp_timeout,vstat:0xa1ff2800,virqc:3fff [ 1.202490@0]h meson-mmc: sd: err: wait for irq service, bus_fsm:0x8 [ 1.202554@2]- Registered swp emulation handler [ 1.203290@2]- Registered cp15_barrier emulation handler [ 1.203295@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:8 [ 1.203298@2]- Registered setend emulation handler [ 1.203427@2]- disable EAS feature [ 1.203878@1]- registered taskstats version 1 [ 1.204305@0]h meson-mmc: sd: resp_timeout,vstat:0xa1ff2800,virqc:3fff [ 1.204438@0]h meson-mmc: sd: err: wait for irq service, bus_fsm:0x8 [ 1.205240@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:8 [ 1.206247@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.206374@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.207215@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:8 [ 1.207218@3]- meson-mmc: Command retried failed line:708, cmd:8 [ 1.208954@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.209077@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.209918@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.209920@3]- meson-mmc: meson_mmc_irq_thread_v3() 686: set 1st retry! [ 1.211728@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.211854@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.212697@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.213086@0]- dwc3 fde00000.dwc3: Configuration mismatch. dr_mode forced to host [ 1.213695@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.213819@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.214663@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.215656@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.215777@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.216618@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.216620@3]- meson-mmc: Command retried failed line:708, cmd:55 [ 1.216867@0]- xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.216892@0]- xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.217686@3]- xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x20810010 [ 1.217720@3]- xhci-hcd xhci-hcd.0.auto: irq 17, io mem 0xfde00000 [ 1.217816@3]- usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.217819@3]- usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.217822@3]- usb usb1: Product: xHCI Host Controller [ 1.217824@3]- usb usb1: Manufacturer: Linux 4.9.269 xhci-hcd [ 1.217826@3]- usb usb1: SerialNumber: xhci-hcd.0.auto [ 1.218258@1]- hub 1-0:1.0: USB hub found [ 1.218279@1]- hub 1-0:1.0: 2 ports detected [ 1.218383@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.218495@1]- xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.218502@1]- xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.218510@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.218540@1]- usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.218600@1]- usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.218602@1]- usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.218604@1]- usb usb2: Product: xHCI Host Controller [ 1.218606@1]- usb usb2: Manufacturer: Linux 4.9.269 xhci-hcd [ 1.218608@1]- usb usb2: SerialNumber: xhci-hcd.0.auto [ 1.218948@2]- hub 2-0:1.0: USB hub found [ 1.218966@2]- hub 2-0:1.0: 1 port detected [ 1.219359@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.219362@3]- meson-mmc: meson_mmc_irq_thread_v3() 686: set 1st retry! [ 1.219396@2]- hctosys: unable to open rtc device (rtc0) [ 1.219668@2]- dwc_otg fdd00000.dwc2_a: dwc_otg_driver_probe(00000000d414bd6a) [ 1.219691@2]- dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: fe03a000, ctrl: 0 [ 1.219702@2]- dwc_otg fdd00000.dwc2_a: base=0xffffff8008e00000 [ 1.219704@2]- dwc_otg fdd00000.dwc2_a: dwc_otg_device=0x000000006f21c08e [ 1.221169@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.221292@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.222136@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.223131@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.223252@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.224093@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.225084@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.225206@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.226047@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.226050@3]- meson-mmc: Command retried failed line:708, cmd:55 [ 1.227799@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.227920@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.228761@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.228763@3]- meson-mmc: meson_mmc_irq_thread_v3() 686: set 1st retry! [ 1.230584@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.230706@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.231547@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.231551@0]- hdmitx: hw: config hdmitx IP vic = 16 cd:6 cs: 2 [ 1.232539@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.232660@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.233501@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.234494@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.234615@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.235456@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.235458@3]- meson-mmc: Command retried failed line:708, cmd:55 [ 1.237199@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.237321@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.238162@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.238164@3]- meson-mmc: meson_mmc_irq_thread_v3() 686: set 1st retry! [ 1.239969@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.240090@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.240937@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.241929@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.242050@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.242891@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.243884@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.244005@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.244845@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:55 [ 1.244847@3]- meson-mmc: Command retried failed line:708, cmd:55 [ 1.246661@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.246784@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.247625@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:1 [ 1.247626@0]- hdmitx: video: Sink is HDMI device [ 1.247628@3]- meson-mmc: meson_mmc_irq_thread_v3() 686: set 1st retry! [ 1.247742@0]- hdmitx: hw: set audio [ 1.247747@0]- hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 1.247757@0]- hdmitx: fs = 3, cd = 6, tmds_clk = 148500 [ 1.247760@0]- hdmitx: hw: aud_n_para = 6144 [ 1.247767@0]- hdmitx: hw: set channel status [ 1.247779@0]- hdmitx: hw: [0x10e3] = 0x1f [ 1.247796@0]- hdmitx: audio: Audio Type: PCM [ 1.247799@0]- hdmitx: system: update rx hdr info d [ 1.247800@0]- hdmitx: hw: set audio [ 1.247801@0]- hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 1.247811@0]- hdmitx: fs = 3, cd = 6, tmds_clk = 148500 [ 1.247812@0]- hdmitx: hw: aud_n_para = 6144 [ 1.247818@0]- hdmitx: hw: set channel status [ 1.247830@0]- hdmitx: hw: [0x10e3] = 0x1f [ 1.247847@0]- hdmitx: audio: Audio Type: PCM [ 1.249432@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.249556@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.250399@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:1 [ 1.251391@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.251513@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.252354@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:1 [ 1.253347@0]h meson-mmc: sd: resp_timeout,vstat:0x9dff0800,virqc:3fff [ 1.253469@0]h meson-mmc: sd: err: wait for desc write back, bus_fsm:0x7 [ 1.254310@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sd: cmd:1 [ 1.254312@3]- meson-mmc: Command retried failed line:708, cmd:1 [ 1.320235@0]- dwc_otg: Core Release: 3.30a [ 1.320239@0]- dwc_otg: Setting default values for core params [ 1.320248@0]- dwc_otg: curmode: 0, host_only: 0 [ 1.320264@0]- dwc_otg fdd00000.dwc2_a: DMA config: BURST_DEFAULT [ 1.332440@0]- dwc_otg: Using Buffer DMA mode [ 1.332443@0]- dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 1.332445@0]- dwc_otg: Working on port type = SLAVE [ 1.332449@0]- dwc_otg: Dedicated Tx FIFOs mode [ 1.334343@0]- meson_cdev probe [ 1.334506@0]- meson_cdev index: 0 [ 1.334666@0]- meson_cdev index: 1 [ 1.334672@0]- cpucore_cooling_register, max_cpu_core_num:4 [ 1.334735@0]- meson_cdev index: 2 [ 1.334753@0]- meson_cdev index: 3 [ 1.334783@0]- find tzd id: 0 [ 1.334888@0]- meson_cdev set min sussces [ 1.334890@0]- meson_cdev probe done [ 1.335026@0]- gxbb_pm: enter meson_pm_probe! [ 1.335030@0]- no vddio3v3_en pin [ 1.335040@0]- pm-meson aml_pm: Can't get switch_clk81 [ 1.335101@0]- gxbb_pm: meson_pm_probe done [ 1.335477@0]- ALSA device list: [ 1.335480@0]- #0: AML-AUGESOUND [ 1.337364@0]- Freeing unused kernel memory: 5888K [ 1.367170@3]- fb: malloc_osd_memory, cma:ffffff800abfb698 [ 1.367176@3]- fb: malloc_osd_memory, 1224, base:0x00000000f0800000, size:8388608 [ 1.367198@3]- fb: use ion buffer for fb memory, fb_index=0 [ 1.367199@3]- fb: OSD0 as afbcd mode,afbc_type=2 [ 1.384199@3]- meson-fb fb: create ion_client ffffffc0c5957e40, handle=00000000d064d241 [ 1.384533@3]- meson-fb fb: ion memory(0): created fb at 0x00000000e8800000, size 75 MiB [ 1.385564@3]- fb: 0, phy: 0x00000000e8800000, vir:0xffffff800acab000, size=77312K [ 1.385564@3]- [ 1.385566@3]- fb: Frame buffer memory assigned at [ 1.385568@3]- fb: 0, phy: 0x00000000e8800000, vir:0xffffff800acab000, size=77312K [ 1.385568@3]- [ 1.385571@3]- fb: 0, phy: 0x00000000e8800000, vir:0xffffff800acab000, size=77312K [ 1.385571@3]- [ 1.385573@3]- fb: logo_index=0,fb_index=0 [ 1.385575@3]- fb: ---------------clear fb0 memory 000000000bccba7c [ 1.398307@3]- fb: osd[0] canvas.idx =0x40 [ 1.398310@3]- fb: osd[0] canvas.addr=0xe8800000 [ 1.398311@3]- fb: osd[0] canvas.width=7680 [ 1.398312@3]- fb: osd[0] canvas.height=2160 [ 1.398313@3]- fb: osd[0] frame.width=1920 [ 1.398315@3]- fb: osd[0] frame.height=1080 [ 1.398316@3]- fb: osd[0] out_addr_id =0x1 [ 1.414606@0]- fb: osd_release now.index=0,open_count=1 [ 1.415903@2]- fb: malloc_osd_memory, cma:ffffff800abfb698 [ 1.415908@2]- fb: malloc_osd_memory, 1224, base:0x00000000f0800000, size:8388608 [ 1.415910@2]- fb: use ion buffer for fb memory, fb_index=1 [ 1.415912@2]- fb: OSD1 as afbcd mode,afbc_type=2 [ 1.416374@2]- meson-fb fb: create ion_client ffffffc0c5957e40, handle=000000004f4ed3a1 [ 1.416703@2]- meson-fb fb: ion memory(1): created fb at 0x00000000ed400000, size 1 MiB [ 1.417723@2]- fb: 1, phy: 0x00000000ed400000, vir:0xffffff8008f01000, size=1024K [ 1.417723@2]- [ 1.417724@2]- fb: Frame buffer memory assigned at [ 1.417727@2]- fb: 1, phy: 0x00000000ed400000, vir:0xffffff8008f01000, size=1024K [ 1.417727@2]- [ 1.417729@2]- fb: 1, phy: 0x00000000ed400000, vir:0xffffff8008f01000, size=1024K [ 1.417729@2]- [ 1.417731@2]- fb: logo_index=0,fb_index=1 [ 1.417733@2]- fb: ---------------clear fb1 memory 00000000ae45285b [ 1.417903@2]- fb: osd[1] canvas.idx =0x43 [ 1.417904@2]- fb: osd[1] canvas.addr=0xed400000 [ 1.417905@2]- fb: osd[1] canvas.width=128 [ 1.417906@2]- fb: osd[1] canvas.height=32 [ 1.417908@2]- fb: osd[1] frame.width=32 [ 1.417909@2]- fb: osd[1] frame.height=32 [ 1.417910@2]- fb: osd[1] out_addr_id =0x2 [ 1.431259@0]- fb: osd_release now.index=1,open_count=1 [ 1.447976@0]- VID: VD1 off [ 1.448101@0]- fb: osd[0] enable: 1 (platform_init) [ 1.464476@0]- fb: osd[1] enable: 0 (platform_init) [ 1.488348@1]- init: ### Loading kernel modules [ 1.489811@2]- init: ### Loading kernel module font [ 1.490699@0]- init: ### Loading kernel module softcursor [ 1.491501@0]- init: ### Loading kernel module bitblit [ 1.492303@0]- init: ### Loading kernel module fbcon [ 1.497758@0]- Console: switching to colour frame buffer device 240x67 [ 1.512516@1]- init: ### Set console font [ 1.514814@2]- init: ### Checking disk(s): LABEL=COREELEC LABEL=STORAGE [ 1.548959@1]- usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 1.689225@1]- usb 1-1: New USB device found, idVendor=1a40, idProduct=0101 [ 1.689230@1]- usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.689232@1]- usb 1-1: Product: USB2.0 HUB [ 1.698816@1]- hub 1-1:1.0: USB hub found [ 1.698926@1]- hub 1-1:1.0: 4 ports detected [ 1.767461@1]- init: ### fsck: couldn't find matching filesystem: LABEL=COREELEC [ 2.462446@1]- init: ### fsck: couldn't find matching filesystem: LABEL=COREELEC [ 2.704992@0]- usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.726397@0]- usb 2-1: New USB device found, idVendor=2174, idProduct=2100 [ 2.726400@0]- usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.726403@0]- usb 2-1: Product: ESD310C [ 2.726405@0]- usb 2-1: Manufacturer: Transcend [ 2.726408@0]- usb 2-1: SerialNumber: 7B2402A6I777968C0007 [ 2.727562@0]- usb-storage 2-1:1.0: USB Mass Storage device detected [ 2.727839@0]- scsi host0: usb-storage 2-1:1.0 [ 3.223821@2]- init: ### fsck: couldn't find matching filesystem: LABEL=COREELEC [ 3.604932@2]- lcd vlock_en=1, vlock_mode=0x4 [ 3.742092@2]- scsi 0:0:0:0: Direct-Access ESD310C TS256GESD310C 1000 PQ: 0 ANSI: 6 [ 3.742993@1]- sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 3.743247@2]- sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB) [ 3.743398@1]- sd 0:0:0:0: [sda] Write Protect is off [ 3.743403@1]- sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 3.743549@1]- sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.744584@3]- sda: sda1 sda2 [ 3.745811@1]- sd 0:0:0:0: [sda] Attached SCSI disk [ 3.986856@1]- init: ### STORAGE: clean, 1349/15597568 files, 1294018/62382678 blocks [ 3.986944@1]- init: ### fsck.fat 4.2 (2021-01-31) [ 3.987042@1]- init: ### /dev/sda1: 111 files, 36986/65501 clusters [ 3.987895@1]- init: ### No filesystem errors found, continuing... [ 3.987993@1]- init: ### Mounting flash [ 3.988053@1]- init: ### mount filesystem LABEL=COREELEC ... [ 4.059531@2]- init: ### Cleaning up flash (if required) [ 4.059929@2]- init: ### mount filesystem /flash/SYSTEM ... [ 4.088691@1]- init: ### Mounting storage [ 4.088884@1]- init: ### mount filesystem LABEL=STORAGE ... [ 4.158013@1]- EXT4-fs (sda2): couldn't mount as ext3 due to feature incompatibilities [ 4.158335@1]- EXT4-fs (sda2): couldn't mount as ext2 due to feature incompatibilities [ 4.175276@1]- EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 4.184312@1]- init: ### Loading bootsplash [ 4.188559@2]- init: ### Checking for updates [ 4.193419@2]- init: ### Preparing system [ 4.209704@3]- init: ### Checking Amlogic DTB [ 4.651500@1]- kernel-overlays-setup: setup base modules [ 4.718074@1]- kernel-overlays-setup: added modules from /usr/lib/kernel-overlays/base/lib/modules/4.9.269 [ 4.767975@2]- kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware [ 4.768463@2]- kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays [ 4.769499@0]- kernel-overlays-setup: done [ 4.852564@2]- systemd[1]: System time before build time, advancing clock. [ 4.872616@2]- cgroup: cgroup2: unknown option "nsdelegate" [ 4.880981@2]- systemd[1]: systemd 255.4 running in system mode (-PAM -AUDIT -SELINUX -APPARMOR -IMA -SMACK -SECCOMP -GCRYPT -GNUTLS -OPENSSL -ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB -ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=hybrid) [ 4.881000@2]- systemd[1]: Detected architecture arm64. [ 4.881703@1]- systemd[1]: Warning! Reported kernel version 4.9.269 is older than systemd's required baseline kernel version 4.15. Your mileage may vary. [ 5.210806@3]- systemd[1]: Queued start job for default target kodi.target. [ 5.223247@0]- Netfilter messages via NETLINK v0.30. [ 5.258822@2]- systemd[1]: Created slice system-modprobe.slice. [ 5.260501@2]- systemd[1]: Created slice system-wg\x2dquick.slice. [ 5.261791@2]- systemd[1]: Created slice user.slice. [ 5.262090@2]- systemd[1]: Started systemd-ask-password-console.path. [ 5.262260@2]- systemd[1]: Started systemd-ask-password-wall.path. [ 5.262474@2]- systemd[1]: Reached target nss-lookup.target. [ 5.262538@2]- systemd[1]: Reached target paths.target. [ 5.262643@2]- systemd[1]: Reached target slices.target. [ 5.276787@2]- systemd[1]: Listening on rpcbind.socket. [ 5.277303@2]- systemd[1]: Reached target rpcbind.target. [ 5.278189@2]- systemd[1]: Listening on systemd-initctl.socket. [ 5.279030@2]- systemd[1]: Listening on systemd-journald-dev-log.socket. [ 5.279629@2]- systemd[1]: Listening on systemd-journald.socket. [ 5.280440@2]- systemd[1]: Listening on systemd-udevd-control.socket. [ 5.280876@2]- systemd[1]: Listening on systemd-udevd-kernel.socket. [ 5.287529@2]- systemd[1]: Mounting dev-mqueue.mount... [ 5.291293@2]- systemd[1]: Mounting sys-kernel-debug.mount... [ 5.294632@2]- systemd[1]: Mounting sys-kernel-tracing.mount... [ 5.298328@3]- systemd[1]: Mounting var.mount... [ 5.309854@0]- systemd[1]: Starting kmod-static-nodes.service... [ 5.313886@0]- systemd[1]: Starting machine-id.service... [ 5.317883@0]- systemd[1]: Starting modprobe@configfs.service... [ 5.325843@3]- systemd[1]: Starting modprobe@drm.service... [ 5.332463@3]- systemd[1]: Starting modprobe@fuse.service... [ 5.339477@0]- systemd[1]: Starting storage-log.service... [ 5.353911@0]- systemd[1]: Starting swap.service... [ 5.363020@2]- fuse init (API version 7.26) [ 5.367605@2]- systemd[1]: Starting systemd-hwdb-update.service... [ 5.373868@0]- systemd[1]: Starting systemd-modules-load.service... [ 5.382760@1]- systemd[1]: Starting systemd-timesyncd-setup.service... [ 5.394137@0]- systemd[1]: Starting systemd-udev-trigger.service... [ 5.400452@2]- systemd[1]: Starting wait-time-sync.service... [ 5.412858@3]- systemd[1]: Mounted dev-mqueue.mount. [ 5.426398@3]- systemd[1]: Mounted sys-kernel-debug.mount. [ 5.427242@3]- systemd[1]: Mounted sys-kernel-tracing.mount. [ 5.427805@3]- systemd[1]: Mounted var.mount. [ 5.429108@3]- systemd[1]: Finished kmod-static-nodes.service. [ 5.430286@3]- systemd[1]: Finished machine-id.service. [ 5.431303@3]- systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 5.431987@3]- systemd[1]: Finished modprobe@configfs.service. [ 5.433034@3]- systemd[1]: modprobe@drm.service: Deactivated successfully. [ 5.433733@3]- systemd[1]: Finished modprobe@drm.service. [ 5.434783@3]- systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 5.435588@3]- systemd[1]: Finished modprobe@fuse.service. [ 5.442123@3]- media: Linux media interface: v0.10 [ 5.466115@3]- Linux video capture interface: v2.00 [ 5.489143@3]- amlvideo-000: V4L2 device registered as video10 [ 5.489154@3]- amlvid:info: v4l2_dev.name=:amlvideo-001 [ 5.489329@3]- amlvideo-001: V4L2 device registered as video23 [ 5.498686@3]- video_framerate_adapter: loading out-of-tree module taints kernel. [ 5.499292@3]- Registered frame rate driver success. [ 5.500906@3]- register clk_set_setting cpu[50] [ 5.502236@3]- Registered firmware driver success. [ 5.502862@3]- Try to load video/h264_enc.bin ... [ 5.507679@3]- load firmware size : 76288, Name : video/h264_enc.bin. [ 5.508380@3]- Try to load video/video_ucode.bin ... [ 5.526287@3]- load firmware size : 1871104, Name : video/video_ucode.bin. [ 5.526504@3]- The fw driver version (v0.2) is lower than the pkg version (v0.3). [ 5.526505@3]- The driver version is too low that may affect the work please update asap. [ 5.564643@3]- Amlogic A/V streaming port init [ 5.572079@1]- no need to register_tync_func. [ 5.572083@1]- no need to register_tync_func. [ 5.572084@1]- no need to register_tync_func. [ 5.572084@1]- no need to register_tync_func. [ 5.572085@1]- no need to register_tync_func. [ 5.572086@1]- no need to register_tync_func. [ 5.572087@1]- no need to register_tync_func. [ 5.572088@1]- no need to register_tync_func. [ 5.572089@1]- no need to register_tync_func. [ 5.572105@1]- get gate demux control failed (null) [ 5.572108@1]- get gate parser_top control failed (null) [ 5.572185@1]- get gate vdec control ok 000000009bf37127 [ 5.572188@1]- get gate clk_81 control failed (null) [ 5.572203@1]- get gate clk_vdec_mux control ok 000000003fdf088f [ 5.572217@1]- get gate clk_hcodec_mux control ok 0000000009a0f2a6 [ 5.572220@1]- get gate clk_hevc_mux control failed (null) [ 5.572239@1]- get gate clk_hevcb_mux control ok 00000000d3df7f50 [ 5.572242@1]- get gate ahbarb0 control failed (null) [ 5.572244@1]- get gate asyncfifo control failed (null) [ 5.572261@1]- get gate clk_hevcf_mux control ok 00000000b3d16792 [ 5.572264@1]- get mux clk err. [ 5.572265@1]- get mux clk err. [ 5.572266@1]- get mux clk err. [ 5.572267@1]- get mux clk err. [ 5.572267@1]- get mux clk err. [ 5.572268@1]- get mux clk err. [ 5.574869@2]- systemd[1]: Finished systemd-timesyncd-setup.service. [ 5.576286@2]- systemd[1]: Finished storage-log.service. [ 5.586173@3]- amvdec_avs module init [ 5.599190@3]- amvdec_h264 module init [ 5.606210@3]- amvdec_h265 module init [ 5.615547@3]- ammvdec_h264 module init [ 5.624754@3]- ammvdec_mpeg12 module init [ 5.627800@3]- ammvdec_mpeg4_driver_init_module [ 5.630603@1]- systemd[1]: Mounting sys-fs-fuse-connections.mount... [ 5.636715@3]- systemd[1]: Mounting sys-kernel-config.mount... [ 5.645864@0]- systemd[1]: var-log.mount was skipped because no trigger condition checks were met. [ 5.649938@0]- systemd[1]: systemd-journald.service: bpf-firewall: Attaching egress BPF program to cgroup /sys/fs/cgroup/unified/system.slice/systemd-journald.service failed: Argument list too long [ 5.658086@1]- systemd[1]: Starting systemd-journald.service... [ 5.661968@0]- systemd[1]: Starting systemd-tmpfiles-setup-dev-early.service... [ 5.664767@1]- decoder registered as /dev/video26 [ 5.667986@1]- amvdec_vc1 module init [ 5.674627@0]- systemd[1]: Finished swap.service. [ 5.675241@0]- systemd[1]: Mounted sys-fs-fuse-connections.mount. [ 5.675254@1]- amvdec_av1 module init [ 5.675736@0]- systemd[1]: Mounted sys-kernel-config.mount. [ 5.676149@0]- systemd[1]: Reached target swap.target. [ 5.690149@1]- amvdec_vp9 module init [ 5.694971@0]- systemd[1]: Mounting tmp.mount... [ 5.702381@2]- systemd-journald[2480]: Collecting audit messages is disabled. [ 5.709358@1]- wifi_dummy: Triggered SDIO/PCIe WiFi power on and bus rescan [ 5.709429@1]- wifi_dummy: found enabled /sdio@fe088000 [ 5.709438@1]- wifi_dummy: found disabled /pcieA@f5000000 [ 5.709484@1]- wifi_dummy: SDIO enabled, PCIe disabled [ 5.709504@1]- aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 481 [ 5.746573@3]- systemd[1]: Mounted tmp.mount. [ 5.798961@1]- systemd[1]: Finished systemd-tmpfiles-setup-dev-early.service. [ 5.801579@0]h cectx fe044000.aocec: bad iniator with self 0x0 [ 5.810200@1]- systemd[1]: Starting systemd-tmpfiles-setup-dev.service... [ 5.871162@1]- systemd[1]: Started systemd-journald.service. [ 5.930415@1]- systemd-journald[2480]: Received client request to flush runtime journal. [ 6.044992@2]- aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 481 [ 6.366356@0]h meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff [ 6.366363@0]h meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8 [ 6.366413@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sdio: cmd:52 [ 6.367461@0]h meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff [ 6.367466@0]h meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8 [ 6.367505@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sdio: cmd:52 [ 6.372667@0]h meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff [ 6.372673@0]h meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8 [ 6.372699@3]- meson-mmc: meson_mmc_irq_thread_v3 656 sdio: cmd:8 [ 6.410845@2]- sdio: queuing unknown CIS tuple 0x80 (2 bytes) [ 6.413706@2]- sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 6.416381@2]- sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 6.421241@2]- sdio: queuing unknown CIS tuple 0x80 (7 bytes) [ 6.553911@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.557711@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.557717@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 0, window start 0, size 5 [ 6.557721@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.561386@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.561393@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 1, window start 0, size 5 [ 6.561397@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.565546@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.565553@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 2, window start 0, size 5 [ 6.565557@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.570103@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.570109@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 3, window start 0, size 5 [ 6.570112@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.574308@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.574315@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 4, window start 0, size 5 [ 6.574320@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.578391@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.578397@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 5, window start 0, size 5 [ 6.578401@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.582210@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 6.582216@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 6, window start 0, size 5 [ 6.582220@2]- meson-mmc: sdio: clk 199999997 tuning start [ 6.588859@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 > [ 6.588866@2]- meson-mmc: sdio: best_win_start =0, best_win_size =4 [ 6.588868@2]- meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x22000 [ 6.590719@2]- sdio: new ultra high speed SDR104 SDIO card at address 0001 [ 6.590725@1]- sdio: clock 199999997, 4-bit-bus-width [ 6.590725@1]- [ 6.591082@1]- meson-mmc: [sdio_reinit] finish [ 6.641644@1]- wireguard: WireGuard 1.0.20220627 loaded. See www.wireguard.com for information. [ 6.641649@1]- wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 7.397900@0]- [0]: vcodec_dec decoder ffffffc0c46fe000 [ 7.398042@0]- [0]: release decoder ffffffc0c46fe000 [ 7.518351@1]- meson_uart fe07a000.serial: ttyS0 use xtal(24M) 24000000 change 921600 to 921600 [ 7.518527@1]- meson_uart fe07a000.serial: ttyS0 use xtal(24M) 24000000 change 921600 to 921600 [ 7.556781@1]- Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 7.760022@1]- Console: switching to colour dummy device 80x25 [ 7.858535@0]- checking watermark status return 0xFFFFFFFF [ 7.858551@0]- optee_armtz: initialized driver [ 8.140426@3]- mali fe400000.bifrost: Continuing without Mali regulator control [ 8.140534@3]- mali fe400000.bifrost: max pp is 2 [ 8.140538@3]- mali fe400000.bifrost: set min pp to default 1 [ 8.140540@3]- mali fe400000.bifrost: min pp is 1 [ 8.140542@3]- mali fe400000.bifrost: set min clk default to 0 [ 8.140544@3]- mali fe400000.bifrost: min clk is 0 [ 8.140560@3]- mali fe400000.bifrost: hiu io source 0x000000008350e77e [ 8.140565@3]- mali fe400000.bifrost: hiu io source 0x00000000072870c3 [ 8.140568@3]- mali fe400000.bifrost: num of pp used most of time 1 [ 8.140570@3]- mali fe400000.bifrost: clock dvfs cfg table size is 6 [ 8.140627@3]- mali fe400000.bifrost: max clk set 4 [ 8.140629@3]- mali fe400000.bifrost: max clk is 4 [ 8.140632@3]- mali fe400000.bifrost: turbo clk set to 5 [ 8.140634@3]- mali fe400000.bifrost: turbo clk is 5 [ 8.140636@3]- mali fe400000.bifrost: default clk set to 4 [ 8.140638@3]- mali fe400000.bifrost: default clk is 4 [ 8.140643@3]- mali fe400000.bifrost: ====================0==================== [ 8.140643@3]- clk_freq= 285714285, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<0 76>, clk_sample=285 [ 8.140647@3]- mali fe400000.bifrost: ====================1==================== [ 8.140647@3]- clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<152 207>, clk_sample=400 [ 8.140650@3]- mali fe400000.bifrost: ====================2==================== [ 8.140650@3]- clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<38 194>, clk_sample=500 [ 8.140653@3]- mali fe400000.bifrost: ====================3==================== [ 8.140653@3]- clk_freq= 666666666, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<150 203>, clk_sample=666 [ 8.140657@3]- mali fe400000.bifrost: ====================4==================== [ 8.140657@3]- clk_freq= 846000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshod=<156 255>, clk_sample=846 [ 8.140661@3]- mali fe400000.bifrost: ====================5==================== [ 8.140661@3]- clk_freq= 846000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshod=<156 255>, clk_sample=846 [ 8.140663@3]- mali fe400000.bifrost: clock dvfs table size is 6 [ 8.143952@3]- mali_plat=000000003a0eda0d [ 8.148797@3]- find tzd id: 0 [ 8.148869@3]- gpu cooling register okay with err=0 [ 8.151726@3]- find tzd id: 0 [ 8.151794@3]- gpu core cooling register okay with err=0 [ 8.151827@3]- shader_present=1, tiler_present=1, l2_present=1 [ 8.151907@3]- Mali_pwr_on:gpu_irq : 200 [ 8.163934@3]- mali fe400000.bifrost: GPU identified as 0x3 arch 7.0.9 r0p0 status 0 [ 8.174924@0]- mali fe400000.bifrost: Probed as mali0 [ 8.403674@2]- dhd_module_init: in Dongle Host Driver, version 100.10.545.8 (r826445-20200303-1) [ 8.403691@2]- ======== dhd_wlan_init_plat_data ======== [ 8.403698@2]- dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=61, oob_irq_flags=0x418 [ 8.403699@2]- dhd_wlan_init_gpio: WL_REG_ON=-1 [ 8.403701@2]- dhd_wifi_platform_load: Enter [ 8.403704@2]- Power-up adapter 'DHD generic adapter' [ 8.403709@2]- wifi_platform_set_power = 1, delay: 200 msec [ 8.403711@2]- ======== PULL WL_REG_ON(-1) HIGH! ======== [ 8.403729@2]- aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 481 [ 8.609643@3]- aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 481 [ 8.808828@2]- Bluetooth: Core ver 2.22 [ 8.808999@2]- NET: Registered protocol family 31 [ 8.809002@2]- Bluetooth: HCI device and connection manager initialized [ 8.809014@2]- Bluetooth: HCI socket layer initialized [ 8.809020@2]- Bluetooth: L2CAP socket layer initialized [ 8.809045@2]- Bluetooth: SCO socket layer initialized [ 8.948977@0]- phy_yt8531_led_fixup in [ 8.961975@3]- meson6-dwmac fdc00000.ethernet eth0: fail to init PTP. [ 8.965245@3]- IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9.005255@3]- proc: unrecognized mount option "hidepid=invisible" or missing value [ 9.192988@1]- wifi_platform_bus_enumerate device present 1 [ 9.193001@1]- ======== Card detection to detect SDIO card! ======== [ 9.193003@1]- sdio_reset_comm(): [ 9.234766@1]- sdio: queuing unknown CIS tuple 0x80 (2 bytes) [ 9.238450@1]- sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 9.241342@2]- sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 9.246309@2]- sdio: queuing unknown CIS tuple 0x80 (7 bytes) [ 9.375604@3]- meson-mmc: sdio: clk 199999997 tuning start [ 9.379321@3]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.379328@3]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 0, window start 0, size 5 [ 9.379331@3]- meson-mmc: sdio: clk 199999997 tuning start [ 9.383334@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.383341@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 1, window start 0, size 5 [ 9.383345@1]- meson-mmc: sdio: clk 199999997 tuning start [ 9.386979@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.386985@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 2, window start 0, size 5 [ 9.386988@1]- meson-mmc: sdio: clk 199999997 tuning start [ 9.390544@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.390549@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 3, window start 0, size 5 [ 9.390553@1]- meson-mmc: sdio: clk 199999997 tuning start [ 9.394119@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.394125@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 4, window start 0, size 5 [ 9.394129@1]- meson-mmc: sdio: clk 199999997 tuning start [ 9.397867@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.397873@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 5, window start 0, size 5 [ 9.397876@1]- meson-mmc: sdio: clk 199999997 tuning start [ 9.401871@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.401883@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 6, window start 0, size 5 [ 9.401890@1]- meson-mmc: sdio: clk 199999997 tuning start [ 9.407206@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 9.407214@2]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 7, window start 0, size 5 [ 9.407219@2]- meson-mmc: sdio: clk 199999997 tuning start [ 9.410489@2]- meson-mmc: sdio: adj_win: < 0 1 2 3 > [ 9.410499@2]- meson-mmc: sdio: best_win_start =0, best_win_size =4 [ 9.410502@2]- meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x22000 [ 9.410512@2]- meson-mmc: [sdio_reinit] finish [ 9.426515@2]- bcmsdh_register: register client driver [ 9.426793@2]- bcmsdh_sdmmc_probe: Enter num=1 [ 9.426913@2]- bcmsdh_sdmmc_probe: Enter num=2 [ 9.426915@2]- bus num (host idx)=2, slot num (rca)=1 [ 9.426918@2]- found adapter info 'DHD generic adapter' [ 9.426939@2]- succeed to alloc static buf [ 9.426983@2]- sdioh_attach: set sd_f2_blocksize 256 [ 9.427019@2]- sdioh_attach: sd clock rate = 0 [ 9.427265@2]- dhdsdio_probe : no mutex held. set lock [ 9.427356@2]- F1 signature read @0x18000000=0x1042aae8 [ 9.430857@1]- F1 signature OK, socitype:0x1 chip:0xaae8 rev:0x2 pkg:0x4 [ 9.431562@1]- DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000 [ 9.431623@1]- [dhd] dhd_conf_set_chiprev : chip=0xaae8, chiprev=2 [ 9.437548@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 9.437556@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 9.437558@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 9.437560@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 9.437562@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 9.437564@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 9.442213@1]- dhd_log_dump_init: kernel log buf size = 512KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 76KB [ 9.442221@1]- dhd_log_dump_init : Try to allocate memory total(4194304) special(8192) [ 9.443027@3]- dhd_attach(): thread:dhd_watchdog_thread:efb started [ 9.443083@3]- dhd_attach(): thread:dhd_dpc:efc started [ 9.443122@3]- dhd_attach(): thread:dhd_rxf:efd started [ 9.443131@3]- dhd_deferred_work_init: work queue initialized [ 9.443138@3]s dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2 [ 9.443250@3]- get_mem_val_from_file: File [/data/vendor/misc/wifi/.memdump.info] doesn't exist [ 9.443255@3]- dhd_get_memdump_info: MEMDUMP ENABLED = 3 [ 9.443261@3]- sdioh_cis_read: func_cis_ptr[0]=0x1070 [ 9.453213@1]- dhdsdio_probe_init: making DHD_BUS_DOWN [ 9.453492@1]- Dongle Host Driver, version 100.10.545.8 (r826445-20200303-1) [ 9.454997@1]- Register interface [wlan0] MAC: 54:78:c9:1b:44:ba [ 9.454997@1]- [ 9.458296@2]- dhd_open: WLAN driver is not initialized [ 9.459221@1]- dhd_dbg_detach_pkt_monitor, 2099 [ 9.459236@1]- dhd_bus_devreset: == Power OFF == [ 9.459631@1]d dhd_bus_stop: making DHD_BUS_DOWN [ 9.459680@1]- bcmsdh_oob_intr_unregister: Enter [ 9.459681@1]- bcmsdh_oob_intr_unregister: irq is not registered [ 9.459694@1]- dhd_bus_devreset: making dhdpub up FALSE [ 9.459701@1]- dhd_txglom_enable: enable 0 [ 9.459704@1]d dhd_bus_devreset: making DHD_BUS_DOWN [ 9.459707@1]- dhd_bus_devreset: WLAN OFF DONE [ 9.459756@1]- wifi_platform_set_power = 0, delay: 0 msec [ 9.459763@1]- ======== PULL WL_REG_ON(-1) LOW! ======== [ 9.459770@1]- dhdsdio_probe : the lock is released. [ 9.459978@1]- dhd_module_init: Exit err=0 [ 10.022779@1]- meson_uart fe080000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600 [ 10.022826@1]- meson_uart fe080000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 9600 [ 10.022837@1]- meson_uart fe080000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200 [ 10.051004@1]- meson_uart fe080000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 2000000 [ 10.492951@2]- dhd_open: Enter wlan0 [ 10.492956@2]- dhd_open : no mutex held. set lock [ 10.492964@2]- [ 10.492964@2]- Dongle Host Driver, version 100.10.545.8 (r826445-20200303-1) [ 10.492981@2]- [dhd-wlan0] wl_android_wifi_on : in g_wifi_on=0 [ 10.492985@2]- wifi_platform_set_power = 1, delay: 200 msec [ 10.492990@2]- ======== PULL WL_REG_ON(-1) HIGH! ======== [ 10.493008@2]- aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 481 [ 10.632852@1]- meson_uart fe080000.serial: ttyS1 use xtal(24M) 24000000 change 2000000 to 115200 [ 10.652994@1]- meson_uart fe080000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 2000000 [ 10.666509@1]- Bluetooth: HCI UART driver ver 2.3 [ 10.666516@1]- Bluetooth: HCI UART protocol H4 registered [ 10.666517@1]- Bluetooth: HCI UART protocol BCSP registered [ 10.666519@1]- Bluetooth: HCI UART protocol LL registered [ 10.666521@1]- Bluetooth: HCI UART protocol ATH3K registered [ 10.666522@1]- Bluetooth: HCI UART protocol Three-wire (H5) registered [ 10.666783@1]- Bluetooth: HCI UART protocol Intel registered [ 10.666891@1]- Bluetooth: HCI UART protocol Broadcom registered [ 10.666893@1]- Bluetooth: HCI UART protocol QCA registered [ 10.666895@1]- Bluetooth: HCI UART protocol AG6XX registered [ 10.666896@1]- Bluetooth: HCI UART protocol Marvell registered [ 10.693041@2]- aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 481 [ 11.204948@2]- sdio_reset_comm(): [ 11.246781@1]- sdio: queuing unknown CIS tuple 0x80 (2 bytes) [ 11.249489@1]- sdio: queuing unknown CIS tuple 0x80 (3 bytes) [ 11.384834@3]- meson-mmc: sdio: clk 199999997 tuning start [ 11.388353@3]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.388360@3]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 0, window start 0, size 5 [ 11.388364@3]- meson-mmc: sdio: clk 199999997 tuning start [ 11.392140@3]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.392155@3]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 1, window start 0, size 5 [ 11.392162@3]- meson-mmc: sdio: clk 199999997 tuning start [ 11.396073@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.396081@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 2, window start 0, size 5 [ 11.396087@1]- meson-mmc: sdio: clk 199999997 tuning start [ 11.399895@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.399902@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 3, window start 0, size 5 [ 11.399907@1]- meson-mmc: sdio: clk 199999997 tuning start [ 11.403484@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.403489@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 4, window start 0, size 5 [ 11.403493@1]- meson-mmc: sdio: clk 199999997 tuning start [ 11.406993@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.406998@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 5, window start 0, size 5 [ 11.407001@1]- meson-mmc: sdio: clk 199999997 tuning start [ 11.410560@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 4 > [ 11.410564@1]- meson-mmc: _aml_sd_emmc_execute_tuning() d1_dly 6, window start 0, size 5 [ 11.410567@1]- meson-mmc: sdio: clk 199999997 tuning start [ 11.413899@1]- meson-mmc: sdio: adj_win: < 0 1 2 3 > [ 11.413903@1]- meson-mmc: sdio: best_win_start =0, best_win_size =4 [ 11.413906@1]- meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x22000 [ 11.413954@1]- sdioh_start: set sd_f2_blocksize 256 [ 11.414226@1]- [ 11.414226@1]- [ 11.414226@1]- dhd_bus_devreset: == Power ON == [ 11.414311@1]- F1 signature read @0x18000000=0x1042aae8 [ 11.417786@1]- F1 signature OK, socitype:0x1 chip:0xaae8 rev:0x2 pkg:0x4 [ 11.418409@1]- DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000 [ 11.418457@1]d dhd_bus_devreset: making DHD_BUS_DOWN [ 11.418496@1]- dhdsdio_probe_init: making DHD_BUS_DOWN [ 11.418705@1]- dhd_os_open_image1: /usr/lib/firmware/brcm/config.txt (507 bytes) open success [ 11.424071@1]- [dhd] dhd_conf_read_country : ccode = SG [ 11.424088@1]- [dhd] dhd_conf_read_others : bcn_timeout = 20 [ 11.424092@1]- [dhd] dhd_conf_read_sdio_params : dhd_slpauto = 0 [ 11.424097@1]- [dhd] dhd_conf_read_pm_params : PM = 0 [ 11.424117@1]- [dhd] dhd_conf_read_nv_by_chip : nv_by_chip_count=16 [ 11.424120@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xa962, chiprev=0, name=nvram_ap6181.txt [ 11.424121@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xa962, chiprev=1, name=nvram_ap6210.txt [ 11.424123@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt [ 11.424125@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt [ 11.424127@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xa9a6, chiprev=2, name=nvram_ap6236.txt [ 11.424129@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4345, chiprev=6, name=nvram_ap6255.txt [ 11.424131@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4345, chiprev=9, name=nvram_ap6256.txt [ 11.424133@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4330, chiprev=4, name=nvram_ap6330.txt [ 11.424135@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4339, chiprev=1, name=nvram_ap6335.txt [ 11.424137@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4354, chiprev=1, name=nvram_ap6354.txt [ 11.424138@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4354, chiprev=2, name=nvram_ap6356.txt [ 11.424140@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4335, chiprev=1, name=nvram_bcm4335.txt [ 11.424142@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xa94c, chiprev=2, name=nvram_ap6234.txt [ 11.424144@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4359, chiprev=9, name=nvram_ap6359s.txt [ 11.424146@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0x4334, chiprev=3, name=nvram_bcm4334.txt [ 11.424148@1]- [dhd] dhd_conf_read_nv_by_chip : chip=0xaae8, chiprev=2, name=nvram_ap6275s.txt [ 11.424163@1]- [dhd] dhd_conf_set_path_params : Final fw_path=/usr/lib/firmware/brcm/fw_bcm43752a2_ag.bin [ 11.424164@1]- [dhd] dhd_conf_set_path_params : Final nv_path=/usr/lib/firmware/brcm/nvram_ap6275s.txt [ 11.424166@1]- [dhd] dhd_conf_set_path_params : Final clm_path=/usr/lib/firmware/brcm/clm_bcm43752a2_ag.blob [ 11.424167@1]- [dhd] dhd_conf_set_path_params : Final conf_path=/usr/lib/firmware/brcm/config.txt [ 11.424623@1]- dhd_os_open_image1: /usr/lib/firmware/brcm/fw_bcm43752a2_ag.bin (685923 bytes) open success [ 11.492830@1]- dhd_os_open_image1: /usr/lib/firmware/brcm/nvram_ap6275s.txt (8361 bytes) open success [ 11.498129@2]- NVRAM version: AP6275S_NVRAM_V1.2.1_20200311 [ 11.498814@1]- dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 11.558861@1]- dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 11.559262@1]- bcmsdh_oob_intr_register: HW_OOB irq=61 flags=0x8 [ 11.559368@1]- bcmsdh_oob_intr_register: disable_irq_wake [ 11.559590@2]- get_mem_val_from_file: File [/data/vendor/misc/wifi/.memdump.info] doesn't exist [ 11.559607@2]- dhd_get_memdump_info: MEMDUMP ENABLED = 3 [ 11.562035@2]s dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1 [ 11.565123@2]- dhd_os_open_image1: /usr/lib/firmware/brcm/clm_bcm43752a2_ag.blob (28865 bytes) open success [ 11.566447@2]- dhd_check_current_clm_data: ----- This FW is not included CLM data ----- [ 11.583466@2]- dhd_check_current_clm_data: ----- This FW is included CLM data ----- [ 11.585757@2]- Firmware up: op_mode=0x0005, MAC=54:78:c9:1b:44:ba [ 11.586247@2]- Disable tdls_auto_op failed. -1 [ 11.590260@2]- dhd_preinit_ioctls: event_log_max_sets: 26 ret: 0 [ 11.600862@2]- Driver: 100.10.545.8 (r826445-20200303-1) [ 11.600862@2]- Firmware: wl0: Dec 4 2019 01:55:28 version 18.35.387.11 (wlan=r853831) FWID 01-ae9dfd3b [ 11.600862@2]- CLM: 9.9.5_SS (2019-12-04 01:26:12) [ 11.601635@2]- dhd_txglom_enable: enable 1 [ 11.601641@2]- [dhd] dhd_conf_set_txglom_params : txglom_mode=copy [ 11.601643@2]- [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0 [ 11.601644@2]- [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, dhd_txminmax=-1 [ 11.601646@2]- [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300 [ 11.601652@2]- [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1 [ 11.603884@2]- dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64 [ 11.605932@2]- dhd_pno_init: Support Android Location Service [ 11.630717@2]- rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23 [ 11.630724@2]- dhd_rtt_init : FTM is not supported [ 11.631248@2]- dhd_rtt_ftm_config : failed to set config [ 11.633614@1]- dhd_ecounter_autoconfig Ecounter autoconfig in fw failed : 0 [ 11.638517@1]- [INIT] logset:8 is preserve/chatty [ 11.639608@1]- [INIT] logset:10 is preserve/chatty [ 11.648259@2]- [dhd] dhd_conf_set_country : set country SG, revision 0 [ 11.653182@2]- [dhd] dhd_conf_set_country : Country code: SG (SG/0) [ 11.659953@2]- [dhd-wlan0] wl_android_wifi_on : Success [ 11.722532@2]- dhd_open : the lock is released. [ 11.722537@2]- dhd_open: Exit wlan0 ret=0 [ 11.722539@2]- [wlan0] tx queue started [ 11.775374@2]- [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0 [ 12.029263@3]d meson6-dwmac fdc00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 12.029289@3]- IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.029423@3]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 12.038589@2]- 8021q: 802.1Q VLAN Support v1.8 [ 12.956991@1]- [TEE] E/TA: MM-module-name:Video firmware TA,Version:1.0.1-gb173c81(build:369) [ 12.956996@1]- [TEE] E/TA: fw_check_pack_version:282 the package has 110 fws totally. [ 12.956998@1]- [TEE] E/TA: fw_check_pack_version:299 The TA ver is v1.0 [ 12.956999@1]- [TEE] E/TA: fw_check_pack_version:300 The fw ver is v0.3 [ 12.957000@1]- [TEE] E/TA: fw_data_insert:379 the fw with 520 KB will be loaded. [ 12.957001@1]- [TEE] M/TA: TEE_Video_Load_FW success [ 12.970240@2]- dovi: disagrees about version of symbol module_layout [ 12.970253@2]- dovi: module license 'AML' taints kernel. [ 12.970255@2]- Disabling lock debugging due to kernel taint [ 12.971856@2]- dovi: disagrees about version of symbol register_dv_functions [ 12.972790@2]- *** amlogic_dolby_vision_init dv: null *** [ 12.972796@2]- *** register_dv_stb_functions.*** [ 12.972880@2]- hdr10_policy 115, ko_info THE GOLDEN FLUENT TECHNOLOGY AND SCIENCE HK LIMITED [stb:2.4:e]-[v1.0]-[ Mon Oct 5 20:07:12 CST 2020]-[ brian.zhu]-[* stb_2.4]-[18510d0c6c2246e2fe28c45ae9f71b68e2bd23fa]-[Date: Sat Oct 3 21:25:19 2020 -0700]-[0] [ 12.972884@2]- efuse_mode=0 reg_value = 0x18 [ 12.972885@2]- dv capability 7 [ 13.006748@1]- Registered IR keymap rc-empty [ 13.007005@1]- input: meson-ir as /devices/platform/fe084040.meson-ir/rc/rc0/input4 [ 13.007187@3]- rc rc0: meson-ir as /devices/platform/fe084040.meson-ir/rc/rc0 [ 13.007622@2]- meson-ir fe084040.meson-ir: receiver initialized [ 13.014044@3]- lirc_dev: IR Remote Control driver registered, major 492 [ 13.020370@2]- rc rc0: lirc_dev: driver ir-lirc-codec (meson-ir) registered at minor = 0 [ 13.020378@2]- IR LIRC bridge handler initialized [ 13.102970@1]- IR NEC protocol handler initialized [ 13.139962@2]- IR RC6 protocol handler initialized [ 13.258286@1]- hdmitx: hdmitx: find SD only 4x3 [ 13.319303@1]- hdmitx: hdmitx: find SD only 4x3 [ 14.470853@1]- hdmitx: hdmitx: find SD only 4x3 [ 14.473231@0]- fb: osd_release now.index=0,open_count=1 [ 14.481537@2]- fb: malloc_osd_memory, cma:ffffff800abfb698 [ 14.481545@2]- fb: malloc_osd_memory, 1224, base:0x00000000f0800000, size:8388608 [ 14.481547@2]- fb: use ion buffer for fb memory, fb_index=2 [ 14.481549@2]- fb: OSD2 as afbcd mode,afbc_type=2 [ 14.482029@2]- meson-fb fb: create ion_client ffffffc0c5957e40, handle=000000005061a2cb [ 14.482033@2]- meson-fb fb: ion memory(2): created fb at 0x00000000ed500000, size 1 MiB [ 14.482036@2]- fb: 2, phy: 0x00000000ed500000, vir:0xffffff8011334000, size=1024K [ 14.482036@2]- [ 14.482038@2]- fb: Frame buffer memory assigned at [ 14.482040@2]- fb: 2, phy: 0x00000000ed500000, vir:0xffffff8011334000, size=1024K [ 14.482040@2]- [ 14.482042@2]- fb: 2, phy: 0x00000000ed500000, vir:0xffffff8011334000, size=1024K [ 14.482042@2]- [ 14.482044@2]- fb: logo_index=0,fb_index=2 [ 14.482046@2]- fb: ---------------clear fb2 memory 00000000c8709a02 [ 14.482219@2]- fb: osd[2] canvas.idx =0x41 [ 14.482220@2]- fb: osd[2] canvas.addr=0xed500000 [ 14.482222@2]- fb: osd[2] canvas.width=128 [ 14.482223@2]- fb: osd[2] canvas.height=32 [ 14.482224@2]- fb: osd[2] frame.width=32 [ 14.482225@2]- fb: osd[2] frame.height=32 [ 14.482226@2]- fb: osd[2] out_addr_id =0x3 [ 14.499437@0]- fb: vpu clkc clock is 199 MHZ [ 14.499467@0]- fb: malloc_osd_memory, cma:ffffff800abfb698 [ 14.499471@0]- fb: malloc_osd_memory, 1224, base:0x00000000f0800000, size:8388608 [ 14.499472@0]- fb: use ion buffer for fb memory, fb_index=3 [ 14.499474@0]- fb: OSD3 as afbcd mode,afbc_type=2 [ 14.501489@0]- meson-fb fb: create ion_client ffffffc0c5957e40, handle=000000000a6d69a5 [ 14.501496@0]- meson-fb fb: ion memory(3): created fb at 0x00000000ed600000, size 8 MiB [ 14.501499@0]- fb: 3, phy: 0x00000000ed600000, vir:0xffffff8011435000, size=8192K [ 14.501499@0]- [ 14.501500@0]- fb: Frame buffer memory assigned at [ 14.501503@0]- fb: 3, phy: 0x00000000ed600000, vir:0xffffff8011435000, size=8192K [ 14.501503@0]- [ 14.501505@0]- fb: 3, phy: 0x00000000ed600000, vir:0xffffff8011435000, size=8192K [ 14.501505@0]- [ 14.501507@0]- fb: logo_index=0,fb_index=3 [ 14.501510@0]- fb: ---------------clear fb3 memory 00000000459e3ca8 [ 14.502858@0]- fb: osd[3] canvas.idx =0x42 [ 14.502859@0]- fb: osd[3] canvas.addr=0xed600000 [ 14.502861@0]- fb: osd[3] canvas.width=128 [ 14.502862@0]- fb: osd[3] canvas.height=32 [ 14.502863@0]- fb: osd[3] frame.width=32 [ 14.502865@0]- fb: osd[3] frame.height=32 [ 14.502866@0]- fb: osd[3] out_addr_id =0x4 [ 14.963428@2]- audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:tdm@1 [ 14.964262@2]- tdm playback mute: 1, lane_cnt = 4 [ 14.964310@2]- audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:tdm@1 [ 14.965007@2]- audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:tdm@1 [ 14.965671@2]- tdm playback mute: 1, lane_cnt = 4 [ 14.965720@0]- audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:tdm@1 [ 14.966426@0]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:i2s2hdmi [ 14.966712@0]- tdm playback mute: 1, lane_cnt = 4 [ 14.966750@0]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:i2s2hdmi [ 14.967489@0]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:i2s2hdmi [ 14.967717@0]- tdm playback mute: 1, lane_cnt = 4 [ 14.967751@0]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:i2s2hdmi [ 14.968444@2]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:i2s2hdmi [ 14.968728@2]- tdm playback mute: 1, lane_cnt = 4 [ 14.968764@2]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:i2s2hdmi [ 14.981875@2]- audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:tdm@1 [ 14.983048@2]- tdm playback mute: 1, lane_cnt = 4 [ 14.983102@2]- audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:tdm@1 [ 14.983787@0]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:i2s2hdmi [ 14.984510@0]- tdm playback mute: 1, lane_cnt = 4 [ 14.984552@0]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:i2s2hdmi [ 14.985312@0]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:spdif@0 [ 14.985785@0]- spdif_a keep clk continuous [ 14.985788@0]- spdif_a keep clk continuous [ 14.985829@0]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:spdif@0 [ 14.986621@2]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:spdif@1 [ 14.987629@2]- spdif_b keep clk continuous [ 14.987632@2]- spdif_b keep clk continuous [ 14.987674@2]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:spdif@1 [ 14.992723@2]- audio_dsp: buf=0 [ 14.992730@2]- audio_dsp: IEC958_mode_raw=0 [ 14.997973@0]- audio_ddr_mngr: frddrs[1] registered by device fe330000.audiobus:i2s2hdmi [ 14.999206@0]- set mclk:11289600, mpll:22579200, get mclk:11289593, mpll:22579186 [ 14.999213@0]- asoc aml_dai_set_tdm_fmt, 0x4001, 0000000033d5650e, id(2), clksel(2) [ 14.999215@0]- aml_tdm_set_fmt(), fmt not change [ 14.999221@0]- dump_pcm_setting(0000000033d5650e) [ 14.999223@0]- pcm_mode(1) [ 14.999225@0]- sysclk(11289600) [ 14.999226@0]- sysclk_bclk_ratio(4) [ 14.999228@0]- bclk(2822400) [ 14.999229@0]- bclk_lrclk_ratio(64) [ 14.999230@0]- lrclk(44100) [ 14.999232@0]- tx_mask(0x3) [ 14.999233@0]- rx_mask(0x3) [ 14.999234@0]- slots(2) [ 14.999235@0]- slot_width(32) [ 14.999236@0]- lane_mask_in(0x0) [ 14.999238@0]- lane_mask_out(0xf) [ 14.999239@0]- lane_oe_mask_in(0x0) [ 14.999240@0]- lane_oe_mask_out(0x0) [ 14.999241@0]- lane_lb_mask_in(0x0) [ 14.999244@0]- set mclk:11289600, mpll:22579200, get mclk:11289593, mpll:22579186 [ 14.999246@0]- aml_tdm_set_clkdiv, div 4, clksel(2) [ 14.999254@0]- aml_set_bclk_ratio, select I2S mode [ 14.999259@0]- aml_tdm_hw_setting_init(), enable mclk for tdm-2 [ 14.999365@0]- aml_tdm_prepare(), reset fddr [ 14.999378@0]- hdmitx: hw: set audio [ 14.999381@0]- hdmitx: hw: hdmitx tx_aud_src = 1, audio_param->channel_num = 1, hdev->aud_output_ch = 33 [ 14.999394@0]- hdmitx: fs = 3, cd = 6, tmds_clk = 148500 [ 14.999397@0]- hdmitx: hw: aud_n_para = 6144 [ 14.999405@0]- hdmitx: hw: set channel status [ 15.024790@0]- hdmitx: hw: [0x10e3] = 0x1f [ 15.024811@0]- hdmitx: audio: Audio Type: PCM [ 15.024815@0]- hdmitx: hw: set audio [ 15.024818@0]- hdmitx: hw: hdmitx tx_aud_src = 1, audio_param->channel_num = 1, hdev->aud_output_ch = 33 [ 15.024830@0]- hdmitx: fs = 2, cd = 6, tmds_clk = 148500 [ 15.024832@0]- hdmitx: hw: aud_n_para = 6272 [ 15.024839@0]- hdmitx: hw: set channel status [ 15.052784@0]- hdmitx: hw: [0x10e3] = 0x1f [ 15.052803@0]- hdmitx: audio: Audio Type: PCM [ 15.052805@0]- hdmitx: audio: set audio param [ 15.052950@0]- tdm playback mute: 0, lane_cnt = 4 [ 15.053073@0]- aml_tdm_prepare(), reset fddr [ 15.053158@0]- tdm playback mute: 0, lane_cnt = 4 [ 15.054917@0]- asoc-aml-card auge_sound: TDM[2] Playback enable [ 15.847393@2]- cectx fe044000.aocec: CEC framework ctrl enabled [ 24.035957@1]- [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, bssidx: 0 [ 40.016062@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 40.016237@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 40.017035@2]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 40.051546@0]- [dhd] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing [ 51.035704@1]- [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2, bssidx: 0 [ 60.410445@3]- fb: mem_free_work, free memory: addr:800000 [ 106.805540@3]- asoc-aml-card auge_sound: TDM[2] Playback stop [ 106.805559@3]- audio_ddr_mngr: frddr stop success, fifo id 1, regbase:0x80, arb sts:0x40000020 [ 106.805609@3]- aml_tdm_prepare(), reset fddr [ 106.805723@3]- tdm playback mute: 0, lane_cnt = 4 [ 116.805609@3]- aml_tdm_hw_setting_free(), disable mclk for tdm-2 [ 116.805639@3]- tdm playback mute: 1, lane_cnt = 4 [ 116.805767@3]- audio_ddr_mngr: frddrs[1] released by device fe330000.audiobus:i2s2hdmi [ 132.099180@1]- [dhd-wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3, bssidx: 0