[ 0.000000@0] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000@0] Linux version 5.4.210 (docker@8024318e9af3) (aarch64-libreelec-linux-gnu-gcc-13.2.0 (GCC) 13.2.0, GNU ld (GNU Binutils) 2.41) #1 SMP PREEMPT Sun Sep 8 02:22:04 IDT 2024 [ 0.000000@0] Machine model: Dune/Homatics R 4K Plus [ 0.000000@0] CoreELEC dt-id: sc2_s905x4_sei_smb_280_id5 [ 0.000000@0] Amlogic dt-id: sc2_s905x4_ah212-id5 [ 0.000000@0] earlycon: aml-uart0 at MMIO 0x00000000fe07a000 (options '') [ 0.000000@0] printk: bootconsole [aml-uart0] enabled [ 0.000000@0] cma_first_wm_low enabled [ 0.000000@0] 08400000 - 08500000, 1024 KB, ramoops@0x07400000 [ 0.000000@0] 05000000 - 08400000, 53248 KB, linux,secmon [ 0.000000@0] 7f800000 - 80000000, 8192 KB, linux,meson-fb [ 0.000000@0] e9000000 - f1000000, 131072 KB, linux,ion-dev [ 0.000000@0] d8000000 - e9000000, 278528 KB, linux,ion-fb [ 0.000000@0] invalid size property in 'linux,ppmgr' node. [ 0.000000@0] a8400000 - d8000000, 782336 KB, linux,codec_mm_cma [ 0.000000@0] a8400000 - a8400000, 0 KB, linux,codec_mm_reserved [ 0.000000@0] a7000000 - a8400000, 20480 KB, linux,vdin1_cma [ 0.000000@0] 30000000 - 30800000, 8192 KB, linux,dsp_fw [ 0.000000@0] cma: dma_contiguous_reserve(limit f1000000) [ 0.000000@0] cma: dma_contiguous_reserve: reserving 8 MiB for global area [ 0.000000@0] cma: Reserved 8 MiB at 0x00000000a6800000 [ 0.000000@0] On node 0 totalpages: 987136 [ 0.000000@0] DMA32 zone: 15424 pages used for memmap [ 0.000000@0] DMA32 zone: 0 pages reserved [ 0.000000@0] DMA32 zone: 987136 pages, LIFO batch:63 [ 0.000000@0] psci: SMC Calling Convention v1.1 [ 0.000000@0] percpu: Embedded 36 pages/cpu s107352 r8192 d31912 u147456 [ 0.000000@0] pcpu-alloc: s107352 r8192 d31912 u147456 alloc=36*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0] CPU features: detected: Virtualization Host Extensions [ 0.000000@0] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000@0] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000@0] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.000000@0] alternatives: patching kernel code [ 0.000000@0] Built 1 zonelists, mobility grouping on. Total pages: 971712 [ 0.000000@0] Kernel command line: systemd.show_status=auto init=/init console=ttyS0,921600 no_console_suspend earlycon=aml-uart,0xfe07a000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 loop.max_part=4 scramble_reg=0xfe02e030 scsi_mod.scan=async xhci_hcd.quirks=0x800000 loglevel=1 otg_device=1 hw_id=5 skip_driver_register=0 cma_first_wm_low=on logo=osd0,loaded,0x00300000 vout=2160p60hz,enable panel_type=lcd_1 hdmitx=,422,12bit hdmimode=1080p60hz hdmichecksum=0x78340000 dolby_vision_on=1 hdr_policy=0 hdr_priority= androidboot.enable_console= config_csc_en=1frac_rate_policy=1 hdmi_read_edid=1 cvbsmode=480cvbs osd_reverse=0 video_reverse=0 irq_check_en=0 androidboot.selinux=enforcing androidboot.firstboot=0 androidboot.sei_kernelLog=0 jtag=disable disable_ir=0 androidboot.bootloader=01.01.231123.172139 androidboot.hardware=amlogic mac=D4:CF:F9:D9:D6:7D androidboot.mac=D4:CF:F9:D9:D6:7D androidboot.serialno=GZ23010171300595 androidboot.oem=ATV00100021000000000000000000B0N androidboot.rpmb_state=0x1 BOOT_IMAGE=kernel.img boot=LABEL=COREELEC disk=LABEL=STORAGE console=tty0 no_console_suspend keymap=us remotewakeup=0xffffffff decode_type=0 remotewakeupmask=0xffffffff vout=1080p60hz,dis logo=osd0,loaded,0x00300000 frac_rate_policy=0 hdmitx=,422,12bit hdr_policy=1 hdr_priority=0 quiet reboot_mode=normal androidboot.vbmeta.device=/dev/block/vbmeta androidboot.vbmeta.avb_version=1.1 androidboot.vbmeta.device_state=locked androidboot.vbmeta.hash_alg=sha256 androidb [ 0.000000@0] aml_media: osd0 [ 0.000000@0] aml_media: loaded [ 0.000000@0] aml_media: 0x00300000 [ 0.000000@0] vout: 2160p60hz [ 0.000000@0] vout: enable: 1 [ 0.000000@0] lcd: panel_type: lcd_1 [ 0.000000@0] get hdmi checksum: 0x78340000 [ 0.000000@0] hdmitx: get hdmi checksum: 0x78340000 [ 0.000000@0] get_amdv_on: 1 [ 0.000000@0] boot hdr_policy: 0 [ 0.000000@0] vpp_axis_reverse: bootargs is 0 [ 0.000000@0] DI: di_read_canvas_reverse: bootargs is 0. [ 0.000000@0] vdin_get_video_reverse: bootargs is 0. [ 0.000000@0] uboot setup mac-addr: d4:cf:f9:d9:d6:7d [ 0.000000@0] vout: 1080p60hz [ 0.000000@0] vout: dis: 0 [ 0.000000@0] aml_media: osd0 [ 0.000000@0] aml_media: loaded [ 0.000000@0] aml_media: 0x00300000 [ 0.000000@0] hdmitx boot frac_rate_policy: 0 [ 0.000000@0] hdmitx: hdmitx boot frac_rate_policy: 0 [ 0.000000@0] boot hdr_policy: 1 [ 0.000000@0] hdmitx boot hdr_priority: 0 [ 0.000000@0] hdmitx: hdmitx boot hdr_priority: 0 [ 0.000000@0] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000@0] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000@0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000@0] Memory: 2537588K/3948544K available (20670K kernel code, 3000K rwdata, 6500K rodata, 7232K init, 1668K bss, 120716K reserved, 1290240K cma-reserved) [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] ftrace: allocating 60527 entries in 237 pages [ 0.000000@0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000@0] rcu: RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000@0] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0] Tasks RCU enabled. [ 0.000000@0] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000@0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000@0] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000@0] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set [ 0.000000@0] irq_meson_gpio: 87 to 12 gpio interrupt mux initialized [ 0.000000@0] rcu: Offload RCU callbacks from CPUs: (none). [ 0.000000@0] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000002@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000297@0] Console: colour dummy device 80x25 [ 0.000303@0] printk: console [tty0] enabled [ 0.000305@0] printk: bootconsole [aml-uart0] disabled [ 0.000330@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.000336@0] pid_max: default: 32768 minimum: 301 [ 0.000407@0] LSM: Security Framework initializing [ 0.000426@0] SELinux: Initializing. [ 0.000493@0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000502@0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.001581@0] ASID allocator initialised with 32768 entries [ 0.001649@0] rcu: Hierarchical SRCU implementation. [ 0.023302@0] secmon: can't fine clear_range [ 0.025298@0] smp: Bringing up secondary CPUs ... [ 0.027086@0] smp: Brought up 1 node, 4 CPUs [ 0.027091@0] SMP: Total of 4 processors activated. [ 0.027094@0] CPU features: detected: Privileged Access Never [ 0.027096@0] CPU features: detected: User Access Override [ 0.027098@0] CPU features: detected: 32-bit EL0 Support [ 0.027100@0] CPU features: detected: Common not Private translations [ 0.027101@0] CPU features: detected: RAS Extension Support [ 0.027103@0] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.027105@0] CPU features: detected: CRC32 instructions [ 0.029834@0] CPU: All CPU(s) started at EL2 [ 0.030524@0] CPU3: update max cpu_capacity 1024 [ 0.031515@1] devtmpfs: initialized [ 0.032190@0] CPU0: update max cpu_capacity 1024 [ 0.044714@1] Registered cp15_barrier emulation handler [ 0.044722@1] Registered setend emulation handler [ 0.044952@1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.044974@1] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.045046@1] xor: measuring software checksum speed [ 0.084225@1] 8regs : 3697.000 MB/sec [ 0.124249@1] 32regs : 4504.000 MB/sec [ 0.164276@1] arm64_neon: 4059.000 MB/sec [ 0.164278@1] xor: using function: 32regs (4504.000 MB/sec) [ 0.164286@1] pinctrl core: initialized pinctrl subsystem [ 0.165077@1] NET: Registered protocol family 16 [ 0.168486@3] DMA: preallocated 256 KiB pool for atomic allocations [ 0.168512@3] audit: initializing netlink subsys (disabled) [ 0.168658@1] audit: type=2000 audit(0.168:1): state=initialized audit_enabled=0 res=1 [ 0.169016@3] cpuidle: using governor menu [ 0.171718@3] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.172771@0] pstore: Registered ramoops as persistent store backend [ 0.172781@0] ramoops: ramoops_io_en:0 1 old:0x0 ftrace_size:0x80000 [ 0.172786@0] ramoops_io_dump=0, buffer=ffffffc0101ff000 ftrace_old_log=0000000000000000, size=0, reboot_mode=normal [ 0.193034@3] audio-clocks fe330000.audio_clocks: no audio top vad clk [ 0.194460@3] audio_clocks: audio_clocks_probe done [ 0.194677@3] aml_snd_reg_map[0], reg:fe331000, size:400 [ 0.194690@3] aml_snd_reg_map[1], reg:fe330000, size:1000 [ 0.194702@3] aml_snd_reg_map[2], reg:fe331400, size:400 [ 0.194715@3] aml_snd_reg_map[3], reg:fe332000, size:1000 [ 0.194727@3] aml_snd_reg_map[4], reg:fe331800, size:400 [ 0.194740@3] aml_snd_reg_map[5], reg:fe331c00, size:104 [ 0.194752@3] aml_snd_reg_map[6], reg:fe334000, size:104 [ 0.194760@3] amlogic auge_snd_iomap probe done [ 0.199388@3] async_long_initcall = 1 [ 0.211263@3] cryptd: max_cpu_qlen set to 1000 [ 0.225605@3] iommu: Default domain type: Translated [ 0.225766@3] vgaarb: loaded [ 0.226006@3] SCSI subsystem initialized [ 0.226133@3] libata version 3.00 loaded. [ 0.226258@3] usbcore: registered new interface driver usbfs [ 0.226292@3] usbcore: registered new interface driver hub [ 0.226315@3] usbcore: registered new device driver usb [ 0.226377@3] mc: Linux media interface: v0.10 [ 0.226402@3] videodev: Linux video capture interface: v2.00 [ 0.226455@3] pps_core: LinuxPPS API ver. 1 registered [ 0.226459@3] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.226469@3] PTP clock support registered [ 0.226928@3] secmon: reserve_mem_size:0x3300000 [ 0.226942@3] secmon secmon: assigned reserved memory node linux,secmon [ 0.228894@3] cpu_version: chip version = 32:D - 2:B [ 0.229276@3] Advanced Linux Sound Architecture Driver Initialized. [ 0.232932@3] clocksource: Switched to clocksource arch_sys_counter [ 0.545815@3] VFS: Disk quotas dquot_6.6.0 [ 0.545862@3] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.552135@1] thermal_sys: Registered thermal governor 'power_allocator' [ 0.552788@1] Total Memory:[f1000000] [ 0.552795@1] ramdump_probe, storage device:data [ 0.552799@1] NO valid ramdump args:0 0 [ 0.553161@1] NET: Registered protocol family 2 [ 0.553331@1] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.554436@2] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.554551@2] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.554751@2] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) [ 0.555077@2] TCP: Hash tables configured (established 32768 bind 32768) [ 0.555231@2] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.555286@2] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.555435@2] NET: Registered protocol family 1 [ 0.555900@2] RPC: Registered named UNIX socket transport module. [ 0.555907@2] RPC: Registered udp transport module. [ 0.555910@2] RPC: Registered tcp transport module. [ 0.555913@2] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.556268@2] NET: Registered protocol family 44 [ 0.557258@2] PCI: CLS 0 bytes, default 64 [ 0.557445@2] aml_wifi aml_wifi: [wifi_dev_probe] use double channel [ 0.557550@2] Wifi: bcmdhd_init_wlan_mem: [dhd] STATIC-MSG) bcmdhd_init_wlan_mem : 101.10.361.10 (wlan=r892223-20210623-1) [ 0.557587@2] fbcon: Taking over console [ 0.560176@2] Wifi: bcmdhd_init_wlan_mem: [dhd] STATIC-MSG) bcmdhd_init_wlan_mem : prealloc ok: 8162304(7971K) [ 0.665298@3] Trying to unpack rootfs image as initramfs... [ 0.685234@3] Freeing initrd memory: 7308K [ 0.688312@3] hw perfevents: no interrupt-affinity property for /arm_pmu, guessing. [ 0.688506@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.692692@1] Initialise system trusted keyrings [ 0.692857@1] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.700421@1] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.701208@1] NFS: Registering the id_resolver key type [ 0.701252@1] Key type id_resolver registered [ 0.701258@1] Key type id_legacy registered [ 0.701269@1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.701273@1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.701980@1] Key type cifs.idmap registered [ 0.702171@1] fuse: init (API version 7.31) [ 0.702557@1] JFS: nTxBlock = 8192, nTxLock = 65536 [ 0.709480@1] SGI XFS with security attributes, no debug enabled [ 0.711138@1] Registering sdcardfs 0.1 [ 0.733275@1] NET: Registered protocol family 38 [ 0.733294@1] Key type asymmetric registered [ 0.733300@1] Asymmetric key parser 'x509' registered [ 0.733341@1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 0.733346@1] io scheduler mq-deadline registered [ 0.733351@1] io scheduler kyber registered [ 0.733498@1] io scheduler bfq registered [ 0.735895@1] Amlogic Meson SC2 (S905X4/C2) Revision 32:d (2:b) Detected [ 0.736350@1] vddcpu0: supplied by regulator-dummy [ 0.737600@3] random: crng init done [ 0.737965@0] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.743315@1] brd: module loaded [ 0.750968@1] loop: module loaded [ 0.751304@1] zram: Added device: zram0 [ 0.752372@1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 0.752381@1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 0.753745@1] tun: Universal TUN/TAP device driver, 1.6 [ 0.754530@1] meson8b-dwmac fdc00000.ethernet: IRQ eth_wake_irq not found [ 0.754540@1] meson8b-dwmac fdc00000.ethernet: IRQ eth_lpi not found [ 0.754618@1] meson8b-dwmac fdc00000.ethernet: PTP uses main clock [ 0.754626@1] meson8b-dwmac fdc00000.ethernet: no reset control found [ 0.755073@1] meson8b-dwmac fdc00000.ethernet: User ID: 0x11, Synopsys ID: 0x37 [ 0.755084@1] meson8b-dwmac fdc00000.ethernet: DWMAC1000 [ 0.755090@1] meson8b-dwmac fdc00000.ethernet: DMA HW capability register supported [ 0.755094@1] meson8b-dwmac fdc00000.ethernet: RX Checksum Offload Engine supported [ 0.755097@1] meson8b-dwmac fdc00000.ethernet: COE Type 2 [ 0.755101@1] meson8b-dwmac fdc00000.ethernet: TX Checksum insertion supported [ 0.755105@1] meson8b-dwmac fdc00000.ethernet: Wake-Up On Lan supported [ 0.755135@1] meson8b-dwmac fdc00000.ethernet: Normal descriptors [ 0.755139@1] meson8b-dwmac fdc00000.ethernet: Ring mode enabled [ 0.755143@1] meson8b-dwmac fdc00000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.755638@1] aml_cust_setting [ 0.755648@1] meson8b-dwmac fdc00000.ethernet: Unable to get resource(385) [ 0.755664@1] no mac_wol [ 0.755667@1] gpio 0 [ 0.755670@1] no keep-alive [ 0.756097@1] PPP generic driver version 2.4.2 [ 0.756258@1] PPP BSD Compression module registered [ 0.756263@1] PPP Deflate Compression module registered [ 0.756286@1] PPP MPPE Compression module registered [ 0.756290@1] NET: Registered protocol family 24 [ 0.756293@1] PPTP driver version 0.8.5 [ 0.757514@1] dwc3 fde00000.dwc3: fde00000.dwc3 supply usb1v8 not found, using dummy regulator [ 0.757648@1] dwc3 fde00000.dwc3: fde00000.dwc3 supply usb3v3 not found, using dummy regulator [ 0.757689@1] dwc3 fde00000.dwc3: fde00000.dwc3 supply usb5v not found, using dummy regulator [ 0.758203@1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.758221@1] ehci-pci: EHCI PCI platform driver [ 0.758613@1] usbcore: registered new interface driver usb-storage [ 0.758677@1] usbcore: registered new interface driver usbserial_generic [ 0.758693@1] usbserial: USB Serial support registered for generic [ 0.759262@1] mousedev: PS/2 mouse device common for all mice [ 0.759309@1] usbcore: registered new interface driver xpad [ 0.759717@1] i2c /dev entries driver [ 0.760627@1] usbcore: registered new interface driver uvcvideo [ 0.760635@1] USB Video Class driver (1.1.1) [ 0.760765@1] meson_gxbb_wdt_set_timeout() timeout=60 [ 0.760771@1] meson_gxbb_wdt_start() [ 0.760778@1] meson-gxbb-wdt fe002100.watchdog: feeding watchdog mode: [kernel] [ 0.788809@1] meson-gx-mmc fe08c000.mmc: host probe success! [ 0.789681@1] meson-gx-mmc fe08a000.sd: Got CD GPIO [ 0.790369@1] meson-gx-mmc fe08a000.sd: Missing clock clkin2 [ 0.817044@1] meson-gx-mmc fe08a000.sd: card OUT [ 0.817072@1] meson-gx-mmc fe08a000.sd: host probe success! [ 0.817549@1] meson-gx-mmc fe088000.sdio: Missing clock clkin2 [ 0.844661@2] meson-gx-mmc fe088000.sdio: host probe success! [ 0.845421@3] ledtrig-cpu: registered to indicate activity on CPUs [ 0.845638@3] hidraw: raw HID events driver (C) Jiri Kosina [ 0.845957@3] usbcore: registered new interface driver usbhid [ 0.845963@3] usbhid: USB HID core driver [ 0.846177@3] ashmem: initialized [ 0.846579@3] meson-saradc fe026000.saradc: fe026000.saradc supply vref not found, using dummy regulator [ 0.847689@3] meson_cpufreq: choose_cpufreq_tables_index:clusterid: 0 tables_index 0 [ 0.848573@3] energy_model: Created perf domain 0-3 [ 0.848609@3] cpu cpu0: meson_cpufreq_init: CPU 0 initialized [ 0.848639@3] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1992000 KHz [ 0.849067@3] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 2004000 KHz [ 0.849978@2] unifykey: fail to obtain phy addr of shared mem [ 0.850980@2] aml_dma fe440400.aml_dma: Aml dma [ 0.853251@2] aml_aes_dma fe440400.aml_dma:aml_aes: Aml AES_dma [ 0.855094@2] aml_sha_dma fe440400.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma [ 0.855913@2] aml_tdes_dma fe440400.aml_dma:aml_tdes: Aml TDES_dma [ 0.856401@3] aml_crypto_dev fe440400.aml_dma:crypto: Aml crypto device [ 0.856983@3] meson_mhu_fifo fe006000.mhu: no get mbox wrrd -22 [ 0.857024@3] meson_mhu_fifo fe006000.mhu: no payload, only use fifo [ 0.857048@3] meson_mhu_fifo fe006000.mhu: set mbox irqmax default value -22 [ 0.857519@2] aml_mailbox: mbox sec init done [ 0.857907@2] ### media_main_init() start [ 0.857913@2] media_configs_system_init [ 0.857927@2] call media_configs_system_init() ret=0 [ 0.858006@2] call dmabuf_manage_init() ret=0 [ 0.858010@2] codec_mm_module_init [ 0.858144@2] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.858177@2] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.858180@2] codec_mm_probe ok [ 0.858265@2] call codec_mm_module_init() ret=0 [ 0.858567@2] Codec io: codec map io source 0xfe002000,size=8192 to 0xffffffc010ae6000 [ 0.858591@2] Codec io: codec map io source 0xfe320000,size=65536 to 0xffffffc010d50000 [ 0.858615@2] Codec io: codec map io source 0xff000000,size=262144 to 0xffffffc010d80000 [ 0.858630@2] Codec io: codec map io source 0xfe036000,size=8192 to 0xffffffc010aea000 [ 0.858644@2] Codec io: codec_io_probe success, cpu_type=0x32 [ 0.858843@2] call codec_io_init() ret=0 [ 0.858850@2] call vdec_reg_ops_init() ret=0 [ 0.859073@2] vpu: vpu: driver version: v20230103(7-sc2) [ 0.859090@2] vpu: vpu: load vpu_clk: 666666667Hz(7) [ 0.859156@2] vpu: vpu: vpu_probe OK [ 0.859305@2] call vpu_init() ret=0 [ 0.859379@2] vclk: aml_vclk_probe OK [ 0.859428@2] call aml_vclk_init_module() ret=0 [ 0.859547@2] call vrr_init() ret=0 [ 0.859655@2] Canvas: canvas_probe ok, reg=fe036048, size=2000 base =ffffffc010bf8048 [ 0.859706@2] call amcanvas_init() ret=0 [ 0.859859@2] rdma: line_n_rdma_en = 0 [ 0.859863@2] rdma: rdma_probe,cpu_type:4, ver:1, len:16,rdma_table_size:65536 [ 0.860377@2] rdma: rdma_register, rdma_table_addr ffffffc010dc1000 phy: a68b0000 reg_buf ffffffb121260000 [ 0.860382@2] rdma: rdma_register success, handle 1 table_size 65536 [ 0.860386@2] rdma: set_rdma_handle video rdma handle = 1. [ 0.860488@2] rdma: rdma_register, rdma_table_addr ffffffc010dd2000 phy: a68c0000 reg_buf ffffffb11ea30000 [ 0.860493@2] rdma: rdma_register success, handle 2 table_size 65536 [ 0.860496@2] rdma: set_rdma_handle video rdma handle = 2. [ 0.860537@2] rdma: rdma_register, rdma_table_addr ffffffc010d45000 phy: a6868000 reg_buf ffffffb11e9f8000 [ 0.860541@2] rdma: rdma_register success, handle 3 table_size 32768 [ 0.860544@2] rdma: set_rdma_handle video rdma handle = 3. [ 0.860735@2] call amrdma_init() ret=0 [ 0.861006@2] call vout_mux_init() ret=0 [ 0.861010@2] call dsc_init() ret=0 [ 0.861127@2] call amhdmitx21_init() ret=0 [ 0.861421@2] hdmitx: system: Ver: 20210902 [ 0.861451@2] hdmitx: system: no hdmitx_i2c of pinctrl state [ 0.861480@2] hdmitx: system: not find match pwr-ctl [ 0.861592@2] hdmitx: get cts_hdmi_axi_clk err [ 0.861869@3] vpu: vpu: vpu_dev_register: vpu_dev 37 in amhdmitx is already registered [ 0.891423@1] Data 1 aligned delay is 0 [ 0.891431@1] mmc0: clk 199999997 div 5 tuning start [ 0.949778@1] mmc0: adj_win: < 0 1 2 3 4 > [ 0.949784@1] mmc0: adj_win: < 0 1 2 3 4 > [ 0.949789@1] meson_mmc_fixadj_tuning() d1_dly 0, window start 0, size 5 [ 0.949793@1] mmc0: clk 199999997 div 5 tuning start [ 0.990375@3] hdmitx: edid: EDID Parser: [ 0.990386@3] [RX]-up_phy_addr = 4 [ 0.990392@3] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 0.990397@3] hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=0 [ 0.990400@3] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 0.990403@3] hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=0 [ 0.990414@3] hdmitx: edid: get dtd0 vic: 4 [ 0.990428@3] hdmitx: edid: get dtd1 vic: 97 [ 0.990432@3] hdmitx: edid: get dtd2 vic: 16 [ 0.990435@3] hdmitx: edid: change preferred_mode from 4 to 97 [ 0.990439@3] hdmitx: hdmitx: get PMT vic: 97 [ 0.990442@3] hdmitx: edid: find IEEEOUT [ 0.990447@3] hdmitx: edid: check sum valid [ 0.990450@3] hdmitx: edid: check sum valid [ 0.990458@3] hdmitx: edid: check sum valid [ 0.990460@3] hdmitx: edid: check sum valid [ 0.990465@3] hdmitx: edid: blk0 raw data [ 0.990486@3] hdmitx: edid: [ 0.990486@3] 00ffffffffffff004dd904aa01010101011e0103807a44780a0dc9a057479827 [ 0.990486@3] 12484c2108008180a9c0714fb300010101010101010108e80030f2705a80b058 [ 0.990486@3] 8a00c2ad4200001e023a801871382d40582c4500c2ad4200001e000000fc0053 [ 0.990486@3] 4f4e5920545620202a30300a000000fd0017790e883c000a2020202020200178 [ 0.990486@3] [ 0.990486@3] [ 0.990489@3] hdmitx: edid: blk1 raw data [ 0.990509@3] hdmitx: edid: [ 0.990509@3] 020364f05861605d5e5f621f101405130420223c3e1203110265663f402f0d7f [ 0.990509@3] 071507503d07bc570601670403830f00006e030c004000b83c2b008001020304 [ 0.990509@3] 67d85dc401788003eb0146d00044038888627697e200cbe305df01e40f030030 [ 0.990509@3] e3060d01011d007251d01e206e285500c2ad4200001e00000000000000000034 [ 0.990509@3] [ 0.990509@3] [ 0.990515@3] hdmitx: hdmitx: get vic 97 cscd 422,12bit [ 0.990518@3] hdmitx: hdmitx: mode name 3840x2160p60hz [ 0.990528@3] hdmitx: hdmitx: tmds clock 594 [ 0.990531@3] hdmitx: hdmitx: act clock: 594 [ 0.994686@2] hdmitx: system: amhdmitx_probe end [ 0.994793@0] hdmitx: system: irq 80000002 0 [ 0.994808@0] hdmitx: UTC+0 1970-01-01 00:00:00 HPD HIGH [ 0.994896@2] call amhdmitx_init() ret=0 [ 0.995223@2] aml_vdac_config_probe: cpu_id:4, name:meson-sc2-vdac [ 0.995226@2] not get cdac_disable. [ 0.995527@2] aml_vdac_probe: ok [ 0.995691@2] call aml_vdac_init() ret=0 [ 0.996008@2] aml_media: register cvbs module server ok [ 0.996013@2] aml_media: register cvbs module vout2 server ok [ 0.996135@1] mmc0: adj_win: < 0 1 2 3 4 > [ 0.996141@1] mmc0: adj_win: < 0 1 2 3 4 > [ 0.996146@1] meson_mmc_fixadj_tuning() d1_dly 1, window start 0, size 5 [ 0.996150@1] mmc0: clk 199999997 div 5 tuning start [ 0.996307@2] call cvbs_init_module() ret=0 [ 0.996563@2] call lcd_init() ret=0 [ 0.996566@2] call peripheral_lcd_init() ret=0 [ 0.996659@2] call esm_init() ret=0 [ 0.996815@2] vpu_security_probe ok. [ 0.996882@2] call vpu_security_init() ret=0 [ 0.997325@2] aml_media: unable to register osd driver, r=0xffffffed [ 0.997341@2] call osd_init_module() ret=-19 [ 0.997525@2] call dummy_venc_init() ret=0 [ 0.997605@2] call vout_sys_serve_init() ret=0 [ 0.997679@2] vout: fr_policy:2 [ 0.997684@2] vout: error: aml_vout_get_dt_info: can't get vsync irq [ 0.997829@3] hdmitx: hdmitx_set_current_vmode[6094] [ 0.997835@3] hdmitx: system: recalc before 1080p60hz 60 1, frac 0 [ 0.997839@3] hdmitx: system: recalc after 1080p60hz 60 1, frac 0 [ 0.997843@3] hdmitx: system: get current mode: 1080p60hz [ 0.997847@3] hdmitx: system: update physical size: 1220 680 [ 0.997863@3] hdmitx: hdmitx: display colourdepth is forced by attr to 12 bits (VIC: 16) [ 0.997884@3] hdmitx: video: already init VIC = 0 Now VIC = 16 [ 0.998908@3] hdmitx: hw: div40: 0 [ 0.999547@1] mmc0: adj_win: < 0 1 2 3 4 > [ 0.999553@1] mmc0: adj_win: < 0 1 2 3 4 > [ 0.999558@1] meson_mmc_fixadj_tuning() d1_dly 2, window start 0, size 5 [ 0.999562@1] mmc0: clk 199999997 div 5 tuning start [ 1.002975@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.002980@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.002984@1] meson_mmc_fixadj_tuning() d1_dly 3, window start 0, size 5 [ 1.002988@1] mmc0: clk 199999997 div 5 tuning start [ 1.006381@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.006387@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.006390@1] meson_mmc_fixadj_tuning() d1_dly 4, window start 0, size 5 [ 1.006394@1] mmc0: clk 199999997 div 5 tuning start [ 1.009767@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.009772@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.009776@1] meson_mmc_fixadj_tuning() d1_dly 5, window start 0, size 5 [ 1.009780@1] mmc0: clk 199999997 div 5 tuning start [ 1.013200@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.013205@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.013209@1] meson_mmc_fixadj_tuning() d1_dly 6, window start 0, size 5 [ 1.013213@1] mmc0: clk 199999997 div 5 tuning start [ 1.016709@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.016714@1] mmc0: adj_win: < 0 1 2 3 4 > [ 1.016718@1] meson_mmc_fixadj_tuning() d1_dly 7, window start 0, size 5 [ 1.016722@1] mmc0: clk 199999997 div 5 tuning start [ 1.019693@1] mmc0: adj_win: < 0 1 3 4 > [ 1.019698@1] mmc0: adj_win: < 0 1 3 4 > [ 1.019701@1] mmc0: best_s = 3, best_sz = 4 [ 1.019705@1] tuning-c:0, tuning-s:4 [ 1.019710@1] mmc0: clk= 0x10000205, adj = 0x2000, dly1 = 0, dly2 = 0 [ 1.020952@1] aml_sd_emmc_clktest [531] clktest : 8704, delay_cell: 73, count: 34 [ 1.020959@1] [tl1_emmc_line_timing], delay1: 0xc30c30c, delay2: 0xc30c [ 1.026952@3] hdmitx: frac_rate = 0 [ 1.026960@3] hdmitx: config HPLL = 5940000 frac_rate = 0 [ 1.027035@3] hdmitx: config HPLL done [ 1.027045@3] hdmitx: set_hpll_od3_clk_div[467] div = 6 [ 1.027052@3] hdmitx: j = 4 vid_clk_div = 1 [ 1.027131@3] hdmitx: set enc for VIC: 16 [ 1.027147@3] hdmitx: hw: config hdmitx IP vic = 16 cd:6 cs: 1 [ 1.027252@0] hdmitx: system: irq 80000001 0 [ 1.040287@3] hdmitx: adjust decouple fifo [ 1.076937@3] hdmitx: video: Sink is HDMI device [ 1.076975@3] hdmitx: hw: set audio [ 1.076989@3] hdmitx: fs = 3, cd = 4, tmds_clk = 148500 [ 1.076994@3] hdmitx: hw: aud_n_para = 6144 [ 1.077004@3] hdmitx: hw: set channel status [ 1.077019@3] hdmitx: hw: [0x10e3] = 0x1f [ 1.077050@3] hdmitx: audio: Audio Type: PCM [ 1.077060@3] vout: init mode 1080p60hz set ok [ 1.077063@3] vout: aml_vout_probe OK [ 1.077171@3] call vout_init_module() ret=0 [ 1.077556@3] call gp_pll_init() ret=0 [ 1.077802@3] ion_dev: __meson_ion_add_heap,heap->name=ion-dev heap->id=8 [ 1.077826@3] ion_dev: __meson_ion_add_heap,heap->name=ion-fb heap->id=9 [ 1.078072@3] ion_dev: __meson_ion_add_heap,heap->name=codec_mm_cma heap->id=16 [ 1.078550@3] call ion_init() ret=0 [ 1.079123@3] call mua_init() ret=0 [ 1.079479@3] call vfm_class_init() ret=0 [ 1.079569@1] scan time distance: 58603541 ns [ 1.079575@1] cmd-best-c:48, cmd-best-size:32 [ 1.080384@3] aml_media: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ [ 1.080479@3] aml_media: ge2d clock is 499 MHZ [ 1.080507@3] aml_media: map io source 0x00000000ffafe646,size=256 to 0x00000000b945a7b2 [ 1.080511@3] aml_media: reserved mem is not used [ 1.081064@3] call ge2d_init_module() ret=0 [ 1.081068@3] vicp_init_module [ 1.081170@2] aml_media: ge2d workqueue monitor start [ 1.081231@3] call vicp_init_module() ret=0 [ 1.081839@3] call configs_init_devices() ret=0 [ 1.082137@3] call lut_dma_init() ret=0 [ 1.082367@3] amvideom_probe, cpu_type=3 [ 1.082412@3] secure_register module=1 ok [ 1.082437@3] amvideom vsync irq: 52 [ 1.082444@3] amvideom meson-amvideom: IRQ vsync_viu2 not found [ 1.082459@3] cannot get amvideom viu2 irq resource [ 1.082497@3] create_ge2d_work_queue video task ok [ 1.082812@3] create amvideo_poll attribute (null) fail [ 1.082972@3] create_video_receiver video_render.0 00000000ca2be5c9, path_id:2 success [ 1.082981@3] create_video_receiver video_render.1 00000000aa0ce986, path_id:3 success [ 1.082995@3] create_video_receiver video_render.2 00000000b1f0422e, path_id:5 success [ 1.083002@3] create_video_receiver video_render.5 00000000651b5a1d, path_id:8 success [ 1.083008@3] create_video_receiver video_render.6 00000000e87e3b95, path_id:9 success [ 1.083026@3] request irq fail, -22 [ 1.083076@3] call video_init() ret=0 [ 1.083108@3] call aml_lcd_extern_i2c_dev_init() ret=0 [ 1.083124@3] call aml_bl_extern_i2c_init() ret=0 [ 1.083254@3] call aml_lcd_extern_init() ret=0 [ 1.083526@3] call aml_bl_init() ret=0 [ 1.083612@3] call aml_bl_extern_init() ret=0 [ 1.083688@3] call ldim_dev_init() ret=0 [ 1.083769@3] call vout2_init_module() ret=0 [ 1.083845@3] call vout3_init_module() ret=0 [ 1.083941@3] PPMGRDRV: info: ppmgr_dev major:505 [ 1.083941@3] [ 1.084074@3] ppmgr driver probe: irq:0 [ 1.084086@3] ppmgr: probe of ppmgr failed with error -22 [ 1.084109@3] call ppmgr_init_module() ret=0 [ 1.084206@3] videosync_create_instance dev_s 00000000f8fee7b6,dev_s->dev 00000000432605d3 [ 1.084210@3] videosync create instance reg videosync.0 [ 1.084300@3] call videosync_init() ret=0 [ 1.084425@3] aml_media: picdec_driver_probe called. [ 1.084430@3] aml_media: picdec_driver_probe reserved_mem is not used. [ 1.084501@3] videosync thread started [ 1.084588@3] call picdec_init_module() ret=0 [ 1.084593@3] amdolby_vision_init:module init [ 1.084869@3] [ 1.084869@3] amdolby_vision probe start & ver: 2023000423 [ 1.084877@3] Can't find multi_core1. [ 1.084881@3] [ 1.084881@3] cpu_id=5 tvmode=0, enable multi_core1 0 [ 1.085024@3] amdv_init_receiver(dvel) [ 1.085029@3] amdv_init_receiver: dvel [ 1.085482@3] get dma_vaddr 0000000057d87703 [ 1.085767@3] amdolby_vision_probe: ok [ 1.085777@3] dovi enable in uboot and mode is LL 422 [ 1.085928@3] call amdolby_vision_init() ret=0 [ 1.086124@3] new arch is :1. [ 1.086128@3] call tsync_module_init() ret=0 [ 1.086176@3] [tsync_pcr_init]init success. [ 1.086180@3] call tsync_pcr_init() ret=0 [ 1.086183@3] video_composer_module_init_1 [ 1.086520@3] video_composer_probe:ports[i].name=video_composer.0, i=0 [ 1.086625@3] video_composer_probe:ports[i].name=video_composer.1, i=1 [ 1.086694@3] video_composer_probe num=2 [ 1.086789@3] call video_composer_module_init() ret=0 [ 1.086793@3] call meson_videotunnel_init() ret=0 [ 1.086796@3] vdetect_init [ 1.086923@3] call vdetect_init() ret=0 [ 1.086927@3] call videoqueue_init() ret=0 [ 1.086930@3] aml_vecm_init:module init [ 1.087176@3] [ 1.087176@3] VECM probe start [ 1.087308@3] hdr dma_vaddr: ffffffc010ed2000 [ 1.087498@3] Can't find lut3d_en. [ 1.087502@3] Can't find ct_3dlut. [ 1.087512@3] vecm chip id: 0, chip_cls : 0 [ 1.087534@3] ID:0x0 map phy: 0xff000000 0x000000006982a412 [ 1.087540@3] ID:0x1 map phy: 0xff63c000 0x00000000c1c6e3a9 [ 1.087544@3] ID:0x2 map phy: 0x0 0x0000000000000000 [ 1.087547@3] Codec io: No support bus type 2 to write. [ 1.087559@3] Codec io: write cbus reg f2 error -1 [ 1.087571@3] vlock clk not cfg [ 1.087581@3] Codec io: No support bus type 2 to read. [ 1.087588@3] Codec io: read cbus reg 20 error -1 [ 1.087595@3] Codec io: No support bus type 2 to read. [ 1.087602@3] Codec io: read cbus reg 21 error -1 [ 1.087611@3] vlock: enc org Line addr:0x1cbb org_enc_line_num val: 524 [ 1.087614@3] vlock: enc org Pixel addr:0x1cb0 val: 1715 [ 1.096930@3] Codec io: No support bus type 2 to read. [ 1.096940@3] Codec io: read cbus reg d1 error -1 [ 1.096947@3] Codec io: No support bus type 2 to write. [ 1.096954@3] Codec io: write cbus reg d1 error -1 [ 1.096961@3] Codec io: No support bus type 2 to read. [ 1.096968@3] Codec io: read cbus reg d1 error -1 [ 1.096975@3] Codec io: No support bus type 2 to write. [ 1.096982@3] Codec io: write cbus reg d1 error -1 [ 1.096994@3] vlock_status_init vlock_en:0 [ 1.096997@3] vlock_status_init vlock_en:0 adj_type:4 mode:0 [ 1.097327@3] aml_vecm_probe: ok [ 1.097427@3] call aml_vecm_init() ret=0 [ 1.097819@3] ionvideo-000: V4L2 device registered as video13 [ 1.098534@3] ionvideo-008: V4L2 device registered as video21 [ 1.098668@3] call ionvideo_init() ret=0 [ 1.098854@3] v4lvideo-000: V4L2 device registered as video30 [ 1.099430@3] v4lvideo-008: V4L2 device registered as video38 [ 1.099435@3] call v4lvideo_init() ret=0 [ 1.099439@3] amlvid:info: amlvideo_init called [ 1.099441@3] amlvid:info: amlvideo_create_instance called [ 1.099441@3] [ 1.099513@3] amlvideo-000: V4L2 device registered as video10 [ 1.099516@3] amlvid:info: amlvideo_create_instance called [ 1.099516@3] [ 1.099522@3] amlvid:info: v4l2_dev.name=:amlvideo-001 [ 1.099522@3] [ 1.099591@3] amlvideo-001: V4L2 device registered as video23 [ 1.099595@3] call amlvideo_init() ret=0 [ 1.099838@3] no match support_4k for amlvideo2.0, disable as default [ 1.100035@3] no match support_4k for amlvideo2.1, disable as default [ 1.100161@3] amlvideo2: V4L2 device registered as video12 [ 1.100224@3] call amlvideo2_init() ret=0 [ 1.100228@3] dil:dil_init. [ 1.100448@3] dil:dil_init ok. [ 1.100451@3] call dil_init() ret=0 [ 1.100455@3] DI: di_module_init ok. [ 1.100560@3] call di_module_init() ret=0 [ 1.100564@3] dim:dim_module_init [ 1.102022@3] dim:name: dim_sc2:id[37]:ver[1] [ 1.102076@3] di_multi multi-di: IRQ aisr_irq not found [ 1.102603@3] dim:afbc_prob:ok:en_ponly_afbcd[0] [ 1.102624@3] dim:cvs inp:0xd9~0xda~0xdb. [ 1.102732@3] dim:hw_init_v3: [ 1.102737@3] dim: 0x17c5:0x1 [ 1.102740@3] dim: 0x17c6:0x1 [ 1.102743@3] dim: 0x1730:0xc3fe0000 [ 1.102776@3] dim:dct_pre_prob:not support [ 1.102924@3] dim:dim_tb_prob:end=0 [ 1.102928@3] . [ 1.103110@3] . [ 1.103235@3] dim:dim_probe:ok [ 1.103364@3] dim:dim_module_init finish [ 1.103369@3] call dim_module_init() ret=0 [ 1.103372@3] di_v4l_init init [ 1.103816@3] di_v4l_init reserved mem is not used. [ 1.103834@3] di_v4l_init out [ 1.103838@3] call di_v4l_init() ret=0 [ 1.104864@3] input: cec_input as /devices/virtual/input/input0 [ 1.105209@3] cec: using cec:1 [ 1.105247@3] cec: not find 'arc_port_mask' [ 1.105428@3] cec: 2 irq src, a:54, b:53 [ 1.106746@1] cec: wakeup_reason:0x0 [ 1.107202@0] check_video_pattern_output: VD0 TESTPATTERN OFF [ 1.107208@0] check_video_pattern_output: VD1 TESTPATTERN OFF [ 1.107212@0] check_video_pattern_output: VD2 TESTPATTERN OFF [ 1.107216@0] check_postblend_pattern_output: VPP TESTPATTERN OFF [ 1.128937@3] hdmitx: [0x10000104]: 0x00000001 [ 1.128945@3] hdmitx: [0x10000180]: 0x000000ff [ 1.128949@3] hdmitx: [0x10000181]: 0x000000ff [ 1.128952@3] hdmitx: [0x10000182]: 0x00000003 [ 1.128956@3] hdmitx: [0x10000183]: 0x00000007 [ 1.128959@3] hdmitx: [0x10000184]: 0x0000003f [ 1.128963@3] hdmitx: [0x10000185]: 0x00000002 [ 1.128966@3] hdmitx: [0x10000187]: 0x000000ff [ 1.128970@3] hdmitx: [0x10000188]: 0x00000003 [ 1.147744@0] cec: wakeup_data: 0x0 0x0 [ 1.147797@0] cec: aml_cec_probe success end [ 1.148132@0] call cec_init() ret=0 [ 1.148604@0] call gdc_driver_init() ret=0 [ 1.148896@0] call adc_init() ret=0 [ 1.149125@0] call tvafe_drv_init() ret=0 [ 1.149227@0] call vbi_init() ret=0 [ 1.149437@0] call tvafe_avin_detect_init() ret=0 [ 1.149631@0] call amvdec_656in_init_module() ret=0 [ 1.149645@0] vdin_drv_init: major 499 ver:20230112 [ 1.149986@0] vdin_drv_init: vdin driver init done [ 1.149990@0] call vdin_drv_init() ret=0 [ 1.150351@0] [RX]-hdmirx_init [ 1.150355@0] call hdmirx_init() ret=0 [ 1.150358@0] ESM HLD: Initializing... [ 1.150784@2] call hld_init() ret=0 [ 1.150789@2] [viuin..]viuin_init_module viuin module init [ 1.151066@2] [viuin..]viuin_probe probe ok. [ 1.151093@2] [viuin..]viuin_init_module done [ 1.151097@2] call viuin_init_module() ret=0 [ 1.151099@2] call resman_init() ret=0 [ 1.151102@2] call aml_atvdemod_init() ret=0 [ 1.151416@2] dtv_dmd:[amldtvdemod..]aml_dtvdemod_init. [ 1.151420@2] call aml_dtvdemod_init() ret=0 [ 1.151423@2] call minfo_init() ret=0 [ 1.151426@2] call msync_init() ret=0 [ 1.151429@2] frc: frc_init:module init [ 1.151511@2] call frc_init() ret=0 [ 1.151515@2] call amlogic_system_secure_dma_buf_init() ret=0 [ 1.151518@2] vpp_drv:vpp_drv_init module init [ 1.151620@2] call vpp_drv_init() ret=0 [ 1.151623@2] call amprime_sl_init() ret=0 [ 1.151626@2] ### media_main_init() end [ 1.151760@2] amvideocap_probe,amvideocap [ 1.151780@2] use cma buf. [ 1.152514@1] Enable disable_nonboot_cpus in syscore shutdown. [ 1.152825@1] hifi4dsp: hifi4dsp_platform_probe of read dsp-cnt=1 [ 1.152830@1] hifi4dsp: hifi4dsp_platform_probe of read dsp_start_mode = 1 [ 1.152834@1] hifi4dsp: hifi4dsp_platform_probe of read dspaoffset=0x00000000 [ 1.152839@1] hifi4dsp: hifi4dsp_platform_probe of read dspboffset=0x00800000 [ 1.152843@1] hifi4dsp: hifi4dsp_platform_probe of read dsp bootlocation=1 [ 1.152846@1] hifi4dsp: Dsp boot from DDR ! [ 1.152876@1] hifi4dsp fe340000.hifi4dsp: assigned reserved memory node linux,dsp_fw [ 1.153439@2] hifi4dsp: of read fwmem phys = [0x30000000 0x800000] [ 1.153449@2] hifi4dsp: [ 1.153449@2] dsp_clk_freqs not configed in dtsi. [ 1.153452@2] hifi4dsp: [ 1.153452@2] register dsp-0 start [ 1.153456@2] hifi4dsp: reserved_mem :base:0x30000000, size:0x800000 [ 1.153553@2] hifi4dsp: [HIGH-MEM-MAP] pa(30800000) to va(0000000041f09151), size: 8388608 [ 1.153558@2] hifi4dsp: hifi4dsp0, firmware :base:0x30000000, size:0x800000, virt:ffffffc011065000 [ 1.153709@3] hifi4dsp: register dsp _p_dsp_miscdev->priv alloc success [ 1.153772@3] hifi4dsp: register dsp-0 done [ 1.153785@3] hifi4dsp: hifi4dsp_platform_probe done [ 1.154489@3] aml_aucpu aucpu: Direct firmware load for aucpu_fw.bin failed with error -2 [ 1.154499@3] load aucpu_fw.bin fail [ 1.154504@1] ds_sht: 16, window:24, intf3:0x410008, clock:0x10160002 [ 1.154508@1] adjust:0x0 [ 1.154511@3] load start_aucpu_fw fail [ 1.154595@1] mmc0: new HS400 MMC card at address 0001 [ 1.154599@3] mmc0: clock 199999997, 8-bit-bus-width [ 1.154599@3] [ 1.154927@3] aml_dvb_extern_init: OK, version: V1.12. [ 1.155235@1] mmcblk0: mmc0:0001 A3A551 28.9 GiB [ 1.155417@3] [drm] [am_meson_vpu_probe] in [ 1.155425@3] [drm] [am_meson_vpu_probe] out [ 1.155534@1] mmcblk0boot0: mmc0:0001 A3A551 partition 1 4.00 MiB [ 1.155858@1] mmcblk0boot1: mmc0:0001 A3A551 partition 2 4.00 MiB [ 1.155920@3] [drm] [am_meson_drv_probe] in [ 1.156033@3] [drm] [am_meson_drv_probe] out [ 1.156186@3] [drm] [am_meson_vpu_bind] in [ 1.156210@3] [drm] id=0,index=0,num_in_links=0,num_out_links=1 [ 1.156213@3] [drm] in_mask=0x0,out_mask=0x10 [ 1.156223@3] [drm] id=1,index=1,num_in_links=0,num_out_links=1 [ 1.156226@3] [drm] in_mask=0x0,out_mask=0x20 [ 1.156235@3] [drm] id=2,index=2,num_in_links=0,num_out_links=1 [ 1.156238@3] [drm] in_mask=0x0,out_mask=0x40 [ 1.156246@3] [drm] id=4,index=0,num_in_links=1,num_out_links=1 [ 1.156249@3] [drm] in_mask=0x1,out_mask=0x800 [ 1.156255@3] [drm] id=5,index=1,num_in_links=1,num_out_links=1 [ 1.156258@3] [drm] in_mask=0x2,out_mask=0x100 [ 1.156265@3] [drm] id=6,index=2,num_in_links=1,num_out_links=1 [ 1.156267@3] [drm] in_mask=0x4,out_mask=0x200 [ 1.156274@3] [drm] id=7,index=0,num_in_links=1,num_out_links=1 [ 1.156277@3] [drm] in_mask=0x1000,out_mask=0x4000 [ 1.156284@3] [drm] id=8,index=1,num_in_links=1,num_out_links=1 [ 1.156288@3] [drm] in_mask=0x20,out_mask=0x800 [ 1.156293@3] [drm] id=9,index=2,num_in_links=1,num_out_links=1 [ 1.156296@3] [drm] in_mask=0x40,out_mask=0x800 [ 1.156303@3] [drm] id=11,index=0,num_in_links=3,num_out_links=2 [ 1.156306@3] [drm] in_mask=0x310,out_mask=0x5000 [ 1.156314@3] [drm] id=12,index=0,num_in_links=1,num_out_links=1 [ 1.156318@1] mmcblk0rpmb: mmc0:0001 A3A551 partition 3 16.0 MiB, chardev (242:0) [ 1.156322@3] [drm] in_mask=0x800,out_mask=0x80 [ 1.156328@3] [drm] id=14,index=0,num_in_links=2,num_out_links=0 [ 1.156331@3] [drm] in_mask=0x880,out_mask=0x0 [ 1.156337@3] [drm] id=17,index=0,num_in_links=0,num_out_links=0 [ 1.156340@3] [drm] in_mask=0x0,out_mask=0x0 [ 1.156355@3] [drm] id=18,index=1,num_in_links=0,num_out_links=0 [ 1.156358@3] [drm] in_mask=0x0,out_mask=0x0 [ 1.156376@3] [drm] undefined crtcmask_of_osd! [ 1.156379@3] [drm] undefined crtcmask_of_video! [ 1.156384@3] [drm] undefined overwrite_crtcmask_of_osd! [ 1.156388@3] [drm] undefined overwrite_crtcmask_of_video! [ 1.156429@3] [drm] osd plane 0 create done, occupied-0 crtc_mask-0 type-1 [ 1.156454@3] [drm] osd plane 1 create done, occupied-0 crtc_mask-0 type-0 [ 1.156473@3] [drm] osd plane 2 create done, occupied-0 crtc_mask-0 type-0 [ 1.156476@3] [drm] create 3 osd plane done [ 1.156481@3] [drm] vfm_mode=1 [ 1.156494@3] [drm] video plane 0 create done [ 1.156505@3] [drm] video plane 1 create done [ 1.156508@3] [drm] create 2 video plane done [ 1.156512@3] [drm] meson_crtc_bind [ 1.156581@3] rdma: rdma_register, rdma_table_addr ffffffc010d26000 phy: 9eade000 reg_buf ffffffb11eadf000 [ 1.156586@3] rdma: rdma_register success, handle 4 table_size 4096 [ 1.156590@3] [drm] meson_vpu_reg_handle_register, vpp0-4 [ 1.156839@3] [drm] [am_meson_vpu_bind] out [ 1.156863@3] meson drm-subsystem: bound ff900000.drm-vpu (ops _etext) [ 1.156870@3] [drm] [meson_hdmitx_dev_bind] in [ 1.156875@3] hdmitx: get_hdmitx_hdcp_ctl_lvl_to_drm hdmitx20_0 [ 1.156877@3] [drm] hdcp_ctl_lvl=0 [ 1.157001@3] [drm] meson_hdmitx_dev_bind[2134] [ 1.157007@3] [drm] [meson_hdmitx_dev_bind] out [ 1.157010@3] hdmitx: meson_hdmitx_bind hdmi [0] [ 1.157020@3] meson drm-subsystem: bound 0.amhdmitx (ops _etext) [ 1.157069@3] [drm] am_drm_writeback creat ok [ 1.157073@3] [drm] mode_config crtc number:1 [ 1.157239@3] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.157244@3] [drm] Driver supports precise vblank timestamp query. [ 1.157265@3] [drm] logo_skip = 0 [ 1.157269@3] [drm] am_meson_logo_init [ 1.157282@3] meson drm-subsystem: assigned reserved memory node linux,meson-fb [ 1.157287@3] [drm] of read reserve memsize=0x800000 [ 1.157798@3] [drm] ------ NO reserved dma [ 1.157814@3] [drm] meson_fb[id:98,ref:1]=0x0000000032f9237d,meson_fb->bufp[0]=0x0000000000000000 [ 1.157818@3] [drm] am_meson_load_logo idx[0] [ 1.157825@3] [drm] logo0 width=1920,height=1080,start_addr=0x0x000000007f800000,size=8388608 [ 1.157828@3] [drm] bpp=16,alloc_flag=1, osd_reverse=0 [ 1.157831@3] [drm] outputmode=1080p60hz [ 1.158223@1] Enter aml_emmc_partition_ops [ 1.158242@3] [drm] Found connector[11] mode[1080p60hz] [ 1.158247@3] [drm] mode private flag 0 [ 1.158263@3] [drm] uboot_mode_init=0 [ 1.158301@3] [drm:meson_hdmitx_atomic_check] *ERROR* hdmitx_on changed, force modeset. [ 1.158391@3] [drm] meson_hdmitx_encoder_atomic_mode_set: enter [ 1.158407@3] [drm] meson_hdmitx_choose_preset_mode validate vmode 1080p60hz, 0 [ 1.158413@3] [drm] build_hdmitx_attr_str:444,10bit = 2+10 [ 1.158425@3] [drm] meson_hdmitx_decide_color_attr get fmt attr [2]+[10] [ 1.158429@3] [drm] build_hdmitx_attr_str:444,10bit = 2+10 [ 1.158436@3] [drm] meson_hdmitx_choose_preset_mode update 1080p60hz expect 0 [ 1.158442@3] [drm] am_meson_crtc_atomic_enable-[0] in: new[1080p60hz], old[], vmode[0-4], uboot[0] [ 1.158448@3] [drm] am_meson_crtc_atomic_enable-[0]: enable mode 1080p60hz final vmode 0 [ 1.158467@3] [drm] am_meson_crtc_atomic_enable-[0]: out [ 1.158471@3] [drm] [meson_hdmitx_encoder_atomic_enable] [ 1.158507@3] hdmitx: hdmitx_set_current_vmode[6094] [ 1.158511@3] hdmitx: system: recalc before 1080p60hz 60 1, frac 0 [ 1.158515@3] hdmitx: system: recalc after 1080p60hz 60 1, frac 0 [ 1.158519@3] hdmitx: system: get current mode: 1080p60hz [ 1.158522@3] hdmitx: system: update physical size: 1220 680 [ 1.158533@3] hdmitx: hdmitx: display colourdepth is forced by attr to 12 bits (VIC: 16) [ 1.158556@3] hdmitx: video: already init VIC = 0 Now VIC = 16 [ 1.158625@1] [mmc_read_partition_tbl] mmc read partition OK! [ 1.158630@1] add_emmc_partition [ 1.158803@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000 [ 1.158911@1] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000 [ 1.158989@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x00000b500000 [ 1.159072@1] [mmcblk0p04] env offset 0x000012900000, size 0x000000800000 [ 1.159149@1] [mmcblk0p05] logo offset 0x000013900000, size 0x000000800000 [ 1.159243@1] [mmcblk0p06] recovery offset 0x000014900000, size 0x000001800000 [ 1.159336@1] [mmcblk0p07] tee offset 0x000016900000, size 0x000002000000 [ 1.159416@1] [mmcblk0p08] factory offset 0x000019100000, size 0x000000800000 [ 1.159493@1] [mmcblk0p09] misc offset 0x00001a100000, size 0x000000200000 [ 1.159574@1] [mmcblk0p10] dtbo offset 0x00001ab00000, size 0x000000200000 [ 1.159585@3] hdmitx: hw: div40: 0 [ 1.159651@1] [mmcblk0p11] cri_data offset 0x00001b500000, size 0x000000800000 [ 1.159732@1] [mmcblk0p12] param offset 0x00001c500000, size 0x000001000000 [ 1.159809@1] [mmcblk0p13] odm_ext offset 0x00001dd00000, size 0x000001000000 [ 1.159887@1] [mmcblk0p14] rsv offset 0x00001f500000, size 0x000001000000 [ 1.159963@1] [mmcblk0p15] oem offset 0x000020d00000, size 0x000003200000 [ 1.160041@1] [mmcblk0p16] metadata offset 0x000024700000, size 0x000001000000 [ 1.160117@1] [mmcblk0p17] vbmeta offset 0x000025f00000, size 0x000000200000 [ 1.160195@1] [mmcblk0p18] vendor_boot offset 0x000026900000, size 0x000001800000 [ 1.160271@1] [mmcblk0p19] frp offset 0x000028900000, size 0x000000200000 [ 1.160347@1] [mmcblk0p20] boot offset 0x000029300000, size 0x000004000000 [ 1.160419@1] [mmcblk0p21] vbmeta_system offset 0x00002db00000, size 0x000000200000 [ 1.160500@1] [mmcblk0p22] super offset 0x00002e500000, size 0x000078400000 [ 1.160580@1] [mmcblk0p23] data offset 0x0000a7100000, size 0x000692f00000 [ 1.160598@1] card key: card_blk_probe. [ 1.160604@1] emmc_key_init:499 emmc key lba_start:0x12020,lba_end:0x12422 [ 1.162290@1] calc c14b1d7727, store c14b1d7727 [ 1.163837@1] calc c14b1d7727, store c14b1d7727 [ 1.163841@1] do nothing [ 1.163854@1] emmc key: emmc_key_init:532 ok. [ 1.163858@1] amlmmc_dtb_init: register dtb chardev [ 1.165435@1] calc 8585c2ad, store 8585c2ad [ 1.166892@1] calc 8585c2ad, store 8585c2ad [ 1.166896@1] total valid 2 [ 1.167036@1] amlmmc_dtb_init: register dtb chardev OK [ 1.167061@1] Exit aml_emmc_partition_ops OK. [ 1.186948@3] hdmitx: frac_rate = 0 [ 1.186963@3] hdmitx: config HPLL = 5940000 frac_rate = 0 [ 1.187039@3] hdmitx: config HPLL done [ 1.187049@3] hdmitx: set_hpll_od3_clk_div[467] div = 6 [ 1.187056@3] hdmitx: j = 4 vid_clk_div = 1 [ 1.187137@3] hdmitx: set enc for VIC: 16 [ 1.187152@3] hdmitx: hw: config hdmitx IP vic = 16 cd:6 cs: 1 [ 1.200292@3] hdmitx: adjust decouple fifo [ 1.236939@3] hdmitx: video: Sink is HDMI device [ 1.236978@3] hdmitx: hw: set audio [ 1.236993@3] hdmitx: fs = 3, cd = 4, tmds_clk = 148500 [ 1.236997@3] hdmitx: hw: aud_n_para = 6144 [ 1.237007@3] hdmitx: hw: set channel status [ 1.237022@3] hdmitx: hw: [0x10e3] = 0x1f [ 1.237053@3] hdmitx: audio: Audio Type: PCM [ 1.237063@3] DOLBY: vout_notify_callback: VOUT_EVENT_MODE_CHANGE [ 1.237093@3] [drm] meson_vout_update_mode_name: hdmitx update vout 1 name 1080p60hz. [ 1.250671@0] [drm] am_meson_load_logo idx[1] [ 1.250689@0] [drm:am_meson_load_logo] *ERROR* NULL MODE or DUMMY MODE, nothing to do. [ 1.250693@0] [drm] vout2 logo is disabled! [ 1.250712@0] [drm] am_meson_load_logo idx[2] [ 1.250717@0] [drm:am_meson_load_logo] *ERROR* NULL MODE or DUMMY MODE, nothing to do. [ 1.250719@0] [drm] vout3 logo is disabled! [ 1.250729@0] [drm] logo_drm_fb[id:98,ref:2] [ 1.250733@0] [drm] am_meson_logo_init end [ 1.250736@0] [drm] am_meson_drm_fbdev_init in [ 1.251180@0] [drm] mode_cmd.width = 4096 [ 1.251184@0] [drm] mode_cmd.height = 4320 [ 1.251187@0] [drm] mode_cmd.pixel_format = 875713089-875713089 [ 1.251203@0] [drm] meson_fb[id:99,ref:1]=0x00000000c227fd22,meson_fb->bufp[0]=0x0000000000000000 [ 1.270904@0] [drm] am_meson_drm_fb_helper_set_par IN [ 1.270914@0] [drm] am_meson_drm_fb_helper_set_par OUT [ 1.270922@0] Console: switching to colour frame buffer device 512x135 [ 1.284108@0] [drm] am_meson_free_logo_memory, free memory: addr:0x0x000000007f800000,size:0x800000 [ 1.501373@2] hdmitx: system: plugin [ 1.633646@2] hdmitx: edid: EDID Parser: [ 1.633658@2] [RX]-up_phy_addr = 4 [ 1.633665@2] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 1.633669@2] hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=0 [ 1.633672@2] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 1.633675@2] hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=0 [ 1.633686@2] hdmitx: edid: get dtd0 vic: 4 [ 1.633699@2] hdmitx: edid: get dtd1 vic: 97 [ 1.633703@2] hdmitx: edid: get dtd2 vic: 16 [ 1.633706@2] hdmitx: edid: change preferred_mode from 4 to 97 [ 1.633709@2] hdmitx: hdmitx: get PMT vic: 97 [ 1.633713@2] hdmitx: edid: find IEEEOUT [ 1.633717@2] hdmitx: edid: check sum valid [ 1.633720@2] hdmitx: edid: check sum valid [ 1.633729@2] hdmitx: edid: check sum valid [ 1.633731@2] hdmitx: edid: check sum valid [ 1.633736@2] hdmitx: edid: blk0 raw data [ 1.633756@2] hdmitx: edid: [ 1.633756@2] 00ffffffffffff004dd904aa01010101011e0103807a44780a0dc9a057479827 [ 1.633756@2] 12484c2108008180a9c0714fb300010101010101010108e80030f2705a80b058 [ 1.633756@2] 8a00c2ad4200001e023a801871382d40582c4500c2ad4200001e000000fc0053 [ 1.633756@2] 4f4e5920545620202a30300a000000fd0017790e883c000a2020202020200178 [ 1.633756@2] [ 1.633756@2] [ 1.633760@2] hdmitx: edid: blk1 raw data [ 1.633779@2] hdmitx: edid: [ 1.633779@2] 020364f05861605d5e5f621f101405130420223c3e1203110265663f402f0d7f [ 1.633779@2] 071507503d07bc570601670403830f00006e030c004000b83c2b008001020304 [ 1.633779@2] 67d85dc401788003eb0146d00044038888627697e200cbe305df01e40f030030 [ 1.633779@2] e3060d01011d007251d01e206e285500c2ad4200001e00000000000000000034 [ 1.633779@2] [ 1.633779@2] [ 1.633783@2] hdmitx: system: update physical size: 1220 680 [ 1.633788@2] hdmitx: system: get current mode: 1080p60hz [ 1.633791@2] hdmitx: system: update physical size: 1220 680 [ 1.633811@2] hdmitx: hdmitx: display colourdepth is forced by attr to 12 bits (VIC: 16) [ 1.633828@2] hdmitx: video: already init VIC = 0 Now VIC = 16 [ 1.634849@2] hdmitx: hw: div40: 0 [ 1.663187@2] hdmitx: frac_rate = 0 [ 1.663195@2] hdmitx: config HPLL = 5940000 frac_rate = 0 [ 1.663269@2] hdmitx: config HPLL done [ 1.663278@2] hdmitx: set_hpll_od3_clk_div[467] div = 6 [ 1.663285@2] hdmitx: j = 4 vid_clk_div = 1 [ 1.663366@2] hdmitx: set enc for VIC: 16 [ 1.663381@2] hdmitx: hw: config hdmitx IP vic = 16 cd:6 cs: 1 [ 1.676516@2] hdmitx: adjust decouple fifo [ 1.712937@2] hdmitx: video: Sink is HDMI device [ 1.712975@2] hdmitx: hw: set audio [ 1.712989@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148500 [ 1.712993@2] hdmitx: hw: aud_n_para = 6144 [ 1.713003@2] hdmitx: hw: set channel status [ 1.713017@2] hdmitx: hw: [0x10e3] = 0x1f [ 1.713048@2] hdmitx: audio: Audio Type: PCM [ 1.713054@2] hdmitx: hw: set audio [ 1.713066@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148500 [ 1.713069@2] hdmitx: hw: aud_n_para = 6144 [ 1.713078@2] hdmitx: hw: set channel status [ 1.713092@2] hdmitx: hw: [0x10e3] = 0x1f [ 1.713121@2] hdmitx: audio: Audio Type: PCM [ 1.713156@2] [drm] drm hdmitx hpd notify [ 1.713163@2] [drm] meson_hdmitx_hpd_cb[1993] [ 2.071972@0] meson drm-subsystem: fb0: mesondrmfb frame buffer device [ 2.072018@0] [drm] create fbdev success. [ 2.072024@0] [drm] create fbdev for primary plane [00000000508e56ea] [ 2.072468@0] [drm] mode_cmd.width = 4096 [ 2.072473@0] [drm] mode_cmd.height = 4320 [ 2.072476@0] [drm] mode_cmd.pixel_format = 875713089-875713089 [ 2.072502@0] [drm] meson_fb[id:101,ref:1]=0x0000000088cdfa69,meson_fb->bufp[0]=0x0000000000000000 [ 2.072996@1] meson drm-subsystem: fb1: mesondrmfb frame buffer device [ 2.073004@1] [drm] create fbdev success. [ 2.073008@1] [drm] create fbdev for plane [1]-[0000000042743611] [ 2.073424@1] [drm] mode_cmd.width = 4096 [ 2.073429@1] [drm] mode_cmd.height = 4320 [ 2.073432@1] [drm] mode_cmd.pixel_format = 875713089-875713089 [ 2.073446@1] [drm] meson_fb[id:98,ref:1]=0x000000008a193b3c,meson_fb->bufp[0]=0x0000000000000000 [ 2.073851@2] meson drm-subsystem: fb2: mesondrmfb frame buffer device [ 2.073857@2] [drm] create fbdev success. [ 2.073862@2] [drm] create fbdev for plane [2]-[000000009b341fe5] [ 2.073866@2] [drm] am_meson_drm_fbdev_init create 3 out [ 2.074528@0] [drm] Initialized meson 2.0.0 20220613 for drm-subsystem on minor 0 [ 2.074992@0] audio_dsp: [dsp]register dsp to char device(272) [ 2.075098@3] amaudio: amaudio: driver amaudio init! [ 2.075285@3] amaudio: amaudio_init - amaudio: driver amaudio success! [ 2.076180@3] gxbb_pm: enter meson_pm_probe! [ 2.076208@3] pm-meson fe010288.pm: Vad enable not detected ~~~ [ 2.076213@3] pm-meson fe010288.pm: Not found item name in dts.The default item will be used! [ 2.076217@3] pm-meson fe010288.pm: Does not match the item type, use the default [init] function. [ 2.076248@3] pm-meson fe010288.pm: Read dmc_asr addr fail [ 2.076254@3] pm-meson fe010288.pm: IRQ pm_wakeup not found [ 2.077096@3] pm-meson fe010288.pm: Failed to get pm_wakeup interrupt source:-6 [ 2.077100@3] gxbb_pm: meson_pm_probe done [ 2.077295@3] bct3236_i2c_probe: loading driver [ 2.083809@3] meson_uart fe07a000.serial: ==uart0 reg addr = 00000000efdff47e [ 2.083850@3] fe07a000.serial: ttyS0 at MMIO 0xfe07a000 (irq = 25, base_baud = 1500000) is a meson_uart [ 2.125635@0] printk: console [ttyS0] enabled [ 2.126186@3] meson_uart fe080000.serial: ==uart1 reg addr = 000000009892af7f [ 2.126900@3] fe080000.serial: ttyS1 at MMIO 0xfe080000 (irq = 43, base_baud = 1500000) is a meson_uart [ 2.127488@3] amlogic rfkill init [ 2.127849@3] request_irq error ret=-22 [ 2.128459@3] dev_pm_set_wake_irq failed: -22 [ 2.129148@3] input: input_btrcu as /devices/platform/aml_bt/input/input1 [ 2.129950@3] amlogic-new-usb2-v2 fe03a000.usb2phy: USB2 phy probe:phy_mem:0xfe03a000, iomap phy_base:0xffffffc010df5000 [ 2.130222@3] amlogic-new-usb3-v2 fe03a080.usb3phy: This is normal phy [ 2.131332@3] amlogic-new-usb3-v2 fe03a080.usb3phy: USB3 phy probe:phy_mem:0xfe03a080, iomap phy_base:0xffffffc010e45080 [ 2.132512@3] bl30_manager: driver init [ 2.133063@3] usbcore: registered new interface driver snd-usb-audio [ 2.133469@3] +es8388_init() [ 2.133728@3] aml_codec_T9015 fe01a000.t9015: aml_T9015_audio_codec_probe [ 2.133825@3] T9015 acodec tdmout index:1 [ 2.134402@3] asoc debug: aml_audio_controller_probe-146 [ 2.135386@3] aml_tdm_platform_probe, tdm ID = 1, lane_cnt = 4 [ 2.135400@3] aml_tdm_platform_probe sys-src clk rate from dts:491520000 [ 2.135407@3] snd_tdm fe330000.audiobus:tdm@1: Can't retrieve suspend-clk-off [ 2.136579@3] TDM id 1 samesource_sel:3 [ 2.136586@3] snd_tdm fe330000.audiobus:tdm@1: lane_mask_out = f [ 2.136657@3] TDM id 1 output clk enable:1 [ 2.136670@3] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 2.136793@3] No channel mask node Channel_Mask [ 2.136807@3] TDM id 1 tuning clk enable:1 [ 2.136888@3] aml_tdm_platform_probe, tdm ID = 2, lane_cnt = 4 [ 2.136901@3] snd_tdm fe330000.audiobus:i2s2hdmi: Can't retrieve suspend-clk-off [ 2.138152@3] TDM id 2 i2s2hdmi:1 [ 2.138158@3] snd_tdm fe330000.audiobus:i2s2hdmi: lane_mask_out = f [ 2.138171@3] snd_tdm fe330000.audiobus:i2s2hdmi: no clk_src_cd clock for 44k case [ 2.138187@3] No channel mask node Channel_Mask [ 2.138788@3] aml_spdif_platform_probe, spdif ID = 0 [ 2.138794@3] snd_spdif fe330000.audiobus:spdif@0: Can't retrieve suspend-clk-off [ 2.140051@3] aml_spdif_parse_of sys-src clk rate from dts:491520000 [ 2.140230@3] Spdif id 0 tuning clk enable:1 [ 2.140286@3] aml_spdif_platform_probe, spdif ID = 1 [ 2.140292@3] snd_spdif fe330000.audiobus:spdif@1: Can't retrieve suspend-clk-off [ 2.141565@3] aml_spdif_parse_of sys-src clk rate from dts:491520000 [ 2.141573@3] snd_spdif fe330000.audiobus:spdif@1: spdif 1 has no pinctrl! [ 2.142156@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 0, irqs toddr 27 [ 2.142166@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 1, irqs toddr 28 [ 2.142176@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 2, irqs toddr 29 [ 2.142185@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 3, irqs toddr 30 [ 2.142195@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 0, irqs frddr 31 [ 2.142204@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 1, irqs frddr 32 [ 2.142213@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 2, irqs frddr 33 [ 2.142223@3] audio-ddr-manager fe330000.audiobus:ddr_manager: 3, irqs frddr 34 [ 2.142668@3] datain_src:4, datain_chnum:0, datain_chumask:0 [ 2.142673@3] datalb_src:1, datalb_chnum:2, datalb_chmask:3 [ 2.142676@3] datain_lane_mask:0x0, datalb_lane_mask:0x1 [ 2.142679@3] datalb_format: 1, chmask for lanes: 0x3 [ 2.142731@3] loopback_platform_probe, p_loopback->id:0 register soc platform [ 2.143587@3] vad_platform_probe, failed to get vad wakeup sample rate [ 2.144604@3] vad_platform_probe, vad wakeup sample rate = 16000 [ 2.144611@3] VAD fe330000.audiobus:vad: check whether to update vad chipinfo [ 2.144658@3] vad_platform_probe vad data source sel:4, level:1 [ 2.144751@3] input: vad_keypad as /devices/platform/soc/fe330000.audiobus/fe330000.audiobus:vad/input/input2 [ 2.145887@1] Register vad [ 2.146234@1] asoc-aml-card auge_sound: IRQ audio_exception64 not found [ 2.147435@1] call standard reset interface [ 2.353334@1] dummy soc:dummy: ASoC: source widget Left DAC overwritten [ 2.353450@1] aml_spdif_new spdif_b, clk continuous:1 [ 2.353455@1] spdifout_play_with_zerodata_free, spdif id:1 [ 2.353468@1] asoc-aml-card auge_sound: SPDIF-B <-> SPDIF-B mapping ok [ 2.353483@1] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 2.353530@1] asoc-aml-card auge_sound: fe01a000.t9015 <-> TDM-B mapping ok [ 2.353571@1] aml_spdif_new spdif_a, clk continuous:1 [ 2.353575@1] spdifout_play_with_zerodata_free, spdif id:0 [ 2.353586@1] audio_ddr_mngr: frddr stop success, fifo id 0, regbase:0x70, arb sts:0x40000010 [ 2.353592@1] asoc-aml-card auge_sound: SPDIF <-> SPDIF mapping ok [ 2.353600@1] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 2.353648@1] asoc-aml-card auge_sound: soc:dummy <-> TDM-C mapping ok [ 2.356334@1] snd_card_add_kcontrols card:00000000543c89ae [ 2.356350@1] effect_v2 is not init [ 2.356376@1] no node audio_effect for eq/drc info! [ 2.356942@1] netem: version 1.3 [ 2.356949@1] u32 classifier [ 2.356952@1] input device check on [ 2.356955@1] Actions configured [ 2.357340@1] gre: GRE over IPv4 demultiplexor driver [ 2.357522@1] Initializing XFRM netlink socket [ 2.357542@1] IPsec XFRM device driver [ 2.357858@1] NET: Registered protocol family 10 [ 2.359124@2] Segment Routing with IPv6 [ 2.359219@2] mip6: Mobile IPv6 [ 2.359388@2] NET: Registered protocol family 17 [ 2.359401@2] NET: Registered protocol family 15 [ 2.359443@2] l2tp_core: L2TP core driver, V2.0 [ 2.359451@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 2.359475@2] Key type dns_resolver registered [ 2.362489@3] registered taskstats version 1 [ 2.362497@3] Loading compiled-in X.509 certificates [ 2.362815@3] Key type ._fscrypt registered [ 2.362819@3] Key type .fscrypt registered [ 2.362823@3] Key type fscrypt-provisioning registered [ 2.363119@3] pstore: Using crash dump compression: deflate [ 2.380374@3] mdio_bus 0.0: ethernet-phy@0 has invalid PHY address [ 2.381344@3] mdio_bus 0.0: scan phy ethernet-phy at address 0 [ 2.437297@3] wzh txamp 0x32 [ 2.439759@3] dwc3 fde00000.dwc3: fde00000.dwc3 supply usb1v8 not found, using dummy regulator [ 2.439904@3] dwc3 fde00000.dwc3: fde00000.dwc3 supply usb3v3 not found, using dummy regulator [ 2.439943@3] dwc3 fde00000.dwc3: fde00000.dwc3 supply usb5v not found, using dummy regulator [ 2.440192@3] amlogic-new-usb2-v2 fe03a000.usb2phy: Not usb-phy-trim-reg [ 2.441281@3] amlogic-new-usb2-v2 fe03a000.usb2phy: Not usb-phy-trim-reg [ 2.445292@3] amlogic-new-usb2-v2 fe03a000.usb2phy: Not usb-phy-trim-reg [ 2.446330@3] amlogic-new-usb2-v2 fe03a000.usb2phy: Not usb-phy-trim-reg [ 2.447565@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.447585@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 2.447720@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000020020810010 [ 2.447760@3] xhci-hcd xhci-hcd.0.auto: irq 67, io mem 0xfde00000 [ 2.447983@3] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 2.447988@3] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.447993@3] usb usb1: Product: xHCI Host Controller [ 2.447997@3] usb usb1: Manufacturer: Linux 5.4.210 xhci-hcd [ 2.448001@3] usb usb1: SerialNumber: xhci-hcd.0.auto [ 2.448380@3] hub 1-0:1.0: USB hub found [ 2.448403@3] hub 1-0:1.0: 2 ports detected [ 2.448619@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.448630@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 2.448640@3] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.448680@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.448748@3] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04 [ 2.448753@3] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.448757@3] usb usb2: Product: xHCI Host Controller [ 2.448761@3] usb usb2: Manufacturer: Linux 5.4.210 xhci-hcd [ 2.448765@3] usb usb2: SerialNumber: xhci-hcd.0.auto [ 2.449065@3] hub 2-0:1.0: USB hub found [ 2.449085@3] hub 2-0:1.0: 1 port detected [ 2.450017@2] meson ts init [ 2.450036@2] tsensor id: 0 [ 2.450060@2] meson-tsensor fe020000.p_tsensor: Does not support reset func.. [ 2.450091@2] tsensor rtemp :110000 [ 2.468950@2] [r1p1_tsensor_read (efault)]valid cnt is 0, tvalue:0 [ 2.489006@2] meson ts init [ 2.489022@2] tsensor id: 1 [ 2.489042@2] meson-tsensor fe022000.d_tsensor: Does not support reset func.. [ 2.489069@2] tsensor rtemp :110000 [ 2.508934@2] [r1p1_tsensor_read (efault)]valid cnt is 0, tvalue:0 [ 2.529318@2] meson_cdev probe [ 2.529330@2] meson_cdev index: 0 [ 2.529554@2] cpucore_cooling_register, max_cpu_core_num:4 [ 2.529610@2] meson_cdev index: 1 [ 2.529617@2] meson_cdev probe done [ 2.530517@2] dwc_otg fdd00000.dwc2_a: dwc_otg_driver_probe(000000006689ba10) [ 2.530549@2] dwc_otg: usb0: type: 2 speed: 0, [ 2.530553@2] config: 0, dma: 0, id: 0, [ 2.530556@2] phy: fe03a000, ctrl: 0 [ 2.530572@2] dwc_otg fdd00000.dwc2_a: base=0xffffffc015f00000 [ 2.530576@2] dwc_otg fdd00000.dwc2_a: dwc_otg_device=0x00000000271250b4 [ 2.531009@2] dwc_otg: Core Release: 3.30a [ 2.531020@2] dwc_otg: Setting default values for core params [ 2.531032@2] dwc_otg: curmode: 0, host_only: 0 [ 2.531051@2] dwc_otg fdd00000.dwc2_a: DMA config: BURST_DEFAULT [ 2.543159@2] dwc_otg: Using Buffer DMA mode [ 2.543166@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 2.543170@2] dwc_otg: Working on port type = SLAVE [ 2.543176@2] dwc_otg: Dedicated Tx FIFOs mode [ 2.544057@2] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.545238@2] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.545520@2] ALSA device list: [ 2.545526@2] #0: AML-AUGESOUND [ 2.549305@2] Freeing unused kernel memory: 7232K [ 2.549504@2] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.549513@2] cfg80211: failed to load regulatory.db [ 2.564959@2] Run /init as init process [ 2.603047@3] [drm] am_meson_drm_fb_helper_set_par IN [ 2.603063@3] [drm] am_meson_drm_fb_helper_set_par OUT [ 2.700948@3] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.849186@3] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.00 [ 2.849196@3] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.849200@3] usb 1-1: Product: USB2.0 HUB [ 2.877224@1] av out status: high [ 2.896880@3] hub 1-1:1.0: USB hub found [ 2.896937@3] hub 1-1:1.0: 4 ports detected [ 3.237286@2] init: ### Loading kernel modules [ 3.237396@2] init: ### Set console font [ 3.240661@0] init: ### Checking disk(s): LABEL=COREELEC LABEL=STORAGE [ 3.558143@3] init: ### fsck: couldn't find matching filesystem: LABEL=COREELEC [ 3.884934@3] lcd vlock_en=0, vlock_mode=0x8 i=101 [ 3.980941@3] usb 1-1.1: new full-speed USB device number 4 using xhci-hcd [ 4.183507@3] usb 1-1.1: New USB device found, idVendor=25a7, idProduct=2402, bcdDevice= 2.00 [ 4.183520@3] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.183525@3] usb 1-1.1: Product: RFIC-MOUSE [ 4.183529@3] usb 1-1.1: Manufacturer: FREEWAY TECHNOLOGY [ 4.276644@3] input: FREEWAY TECHNOLOGY RFIC-MOUSE Keyboard as /devices/platform/soc/soc:usb@fde00000/fde00000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:25A7:2402.0001/input/input3 [ 4.309056@0] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd [ 4.310351@1] init: ### fsck: couldn't find matching filesystem: LABEL=COREELEC [ 4.329855@0] usb 2-1: New USB device found, idVendor=0781, idProduct=5583, bcdDevice= 1.00 [ 4.329867@0] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.329872@0] usb 2-1: Product: Ultra Fit [ 4.329876@0] usb 2-1: Manufacturer: SanDisk [ 4.329881@0] usb 2-1: SerialNumber: 4C530000090311111295 [ 4.330856@0] usb-storage 2-1:1.0: USB Mass Storage device detected [ 4.331255@0] scsi host0: usb-storage 2-1:1.0 [ 4.333414@3] input: FREEWAY TECHNOLOGY RFIC-MOUSE Consumer Control as /devices/platform/soc/soc:usb@fde00000/fde00000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:25A7:2402.0001/input/input4 [ 4.333565@3] input: FREEWAY TECHNOLOGY RFIC-MOUSE System Control as /devices/platform/soc/soc:usb@fde00000/fde00000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:25A7:2402.0001/input/input5 [ 4.333695@3] input: FREEWAY TECHNOLOGY RFIC-MOUSE as /devices/platform/soc/soc:usb@fde00000/fde00000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:25A7:2402.0001/input/input6 [ 4.333947@3] hid-generic 0003:25A7:2402.0001: input,hiddev96,hidraw0: USB HID v1.01 Keyboard [FREEWAY TECHNOLOGY RFIC-MOUSE] on usb-xhci-hcd.0.auto-1.1/input0 [ 4.335696@3] input: FREEWAY TECHNOLOGY RFIC-MOUSE as /devices/platform/soc/soc:usb@fde00000/fde00000.dwc3/xhci-hcd.0.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:25A7:2402.0002/input/input8 [ 4.335938@3] hid-generic 0003:25A7:2402.0002: input,hidraw1: USB HID v1.01 Mouse [FREEWAY TECHNOLOGY RFIC-MOUSE] on usb-xhci-hcd.0.auto-1.1/input1 [ 5.057204@1] init: ### fsck: couldn't find matching filesystem: LABEL=COREELEC [ 5.346406@0] scsi 0:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 5.347304@2] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.347927@0] sd 0:0:0:0: [sda] 60063744 512-byte logical blocks: (30.8 GB/28.6 GiB) [ 5.364222@0] sd 0:0:0:0: [sda] Write Protect is off [ 5.364233@0] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 5.374427@0] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.457323@0] sda: sda1 sda2 [ 5.460033@0] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 5.941750@3] init: ### fsck.fat 4.2 (2021-01-31) [ 5.941908@3] init: ### /dev/sda1: 40 files, 33550/65501 clusters [ 5.942085@3] init: ### STORAGE: clean, 1068/7376896 files, 1866799/29503488 blocks [ 5.943207@1] init: ### No filesystem errors found, continuing... [ 5.943344@1] init: ### Mounting flash [ 5.943426@1] init: ### mount filesystem LABEL=COREELEC ... [ 6.090012@1] init: ### Cleaning up flash (if required) [ 6.090448@1] init: ### mount filesystem /flash/SYSTEM ... [ 6.161985@0] init: ### Mounting storage [ 6.162160@0] init: ### mount filesystem LABEL=STORAGE ... [ 6.337150@0] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 6.409124@0] init: ### Loading bootsplash [ 6.414760@1] init: ### Checking for updates [ 6.420844@3] init: ### Preparing system [ 6.451978@1] init: ### Checking Amlogic DTB [ 6.722227@2] ### BIG FAT WARNING [ 6.722277@2] ### sda2 is removable. suspend/resume may not work [ 6.727598@2] ### BIG FAT WARNING [ 6.727645@2] ### sda1 is removable. suspend/resume may not work [ 6.828895@1] kernel-overlays-setup: setup base modules [ 6.885954@1] kernel-overlays-setup: added modules from /usr/lib/kernel-overlays/base/lib/modules/5.4.210 [ 6.943277@1] kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware [ 6.944891@1] kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays [ 6.956895@0] kernel-overlays-setup: done [ 7.114149@1] systemd[1]: System time before build time, advancing clock. [ 7.153195@1] systemd[1]: systemd 255.4 running in system mode (-PAM -AUDIT -SELINUX -APPARMOR -IMA -SMACK -SECCOMP -GCRYPT -GNUTLS -OPENSSL -ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB -ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=hybrid) [ 7.153219@1] systemd[1]: Detected architecture arm64. [ 7.439879@1] systemd[1]: Queued start job for default target kodi.target. [ 7.476029@3] systemd[1]: Created slice system-modprobe.slice. [ 7.477589@3] systemd[1]: Created slice user.slice. [ 7.477960@3] systemd[1]: Started systemd-ask-password-console.path. [ 7.478156@3] systemd[1]: Started systemd-ask-password-wall.path. [ 7.478310@3] systemd[1]: Reached target nss-lookup.target. [ 7.478358@3] systemd[1]: Reached target paths.target. [ 7.478435@3] systemd[1]: Reached target slices.target. [ 7.493382@3] systemd[1]: Listening on rpcbind.socket. [ 7.493585@3] systemd[1]: Reached target rpcbind.target. [ 7.494405@3] systemd[1]: Listening on systemd-initctl.socket. [ 7.496453@3] systemd[1]: Listening on systemd-journald-dev-log.socket. [ 7.497506@3] systemd[1]: Listening on systemd-journald.socket. [ 7.498572@3] systemd[1]: Listening on systemd-udevd-control.socket. [ 7.499015@3] systemd[1]: Listening on systemd-udevd-kernel.socket. [ 7.504661@3] systemd[1]: Mounting dev-mqueue.mount... [ 7.508565@3] systemd[1]: Mounting sys-kernel-debug.mount... [ 7.514694@3] systemd[1]: Mounting sys-kernel-tracing.mount... [ 7.518626@3] systemd[1]: Mounting var.mount... [ 7.523669@3] systemd[1]: Starting kmod-static-nodes.service... [ 7.529290@3] systemd[1]: Starting machine-id.service... [ 7.542733@3] systemd[1]: Starting modprobe@configfs.service... [ 7.549427@3] systemd[1]: Starting modprobe@drm.service... [ 7.554161@3] systemd[1]: Starting modprobe@fuse.service... [ 7.558740@3] systemd[1]: Starting storage-log.service... [ 7.570298@3] systemd[1]: Starting swap.service... [ 7.586330@3] systemd[1]: Starting systemd-hwdb-update.service... [ 7.677966@1] systemd[1]: Starting systemd-modules-load.service... [ 7.682736@0] systemd[1]: Starting systemd-timesyncd-setup.service... [ 7.692334@0] systemd[1]: Starting systemd-udev-trigger.service... [ 7.709509@3] systemd[1]: Starting wait-time-sync.service... [ 7.719014@3] systemd[1]: Mounted dev-mqueue.mount. [ 7.719490@3] systemd[1]: Mounted sys-kernel-debug.mount. [ 7.719931@3] systemd[1]: Mounted sys-kernel-tracing.mount. [ 7.720331@3] systemd[1]: Mounted var.mount. [ 7.721551@3] systemd[1]: Finished kmod-static-nodes.service. [ 7.722595@3] systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 7.723360@3] systemd[1]: Finished modprobe@configfs.service. [ 7.724341@3] systemd[1]: modprobe@drm.service: Deactivated successfully. [ 7.725090@3] systemd[1]: Finished modprobe@drm.service. [ 7.726036@3] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 7.726747@3] systemd[1]: Finished modprobe@fuse.service. [ 7.733819@3] systemd[1]: Mounting sys-fs-fuse-connections.mount... [ 7.738423@3] systemd[1]: Mounting sys-kernel-config.mount... [ 7.743074@3] systemd[1]: Starting systemd-tmpfiles-setup-dev-early.service... [ 7.744875@3] systemd[1]: Finished storage-log.service. [ 7.753272@3] systemd[1]: var-log.mount was skipped because no trigger condition checks were met. [ 7.757113@1] systemd[1]: Mounted sys-fs-fuse-connections.mount. [ 7.764096@1] systemd[1]: Finished machine-id.service. [ 7.770437@1] systemd[1]: Starting systemd-journald.service... [ 7.774090@1] systemd[1]: Mounted sys-kernel-config.mount. [ 7.789009@0] systemd[1]: Finished systemd-timesyncd-setup.service. [ 7.790947@1] wifi_dummy: loading out-of-tree module taints kernel. [ 7.791288@1] Triggered SDIO/PCI WiFi power on and bus rescan. [ 7.791307@1] aml_wifi aml_wifi: [pci_remove] pci remove! [ 7.839604@1] systemd-journald[418]: Collecting audit messages is disabled. [ 7.875870@1] systemd[1]: Finished systemd-tmpfiles-setup-dev-early.service. [ 7.890159@3] systemd[1]: Starting systemd-tmpfiles-setup-dev.service... [ 7.958371@2] systemd[1]: Finished systemd-tmpfiles-setup-dev.service. [ 7.958938@2] systemd[1]: Reached target local-fs-pre.target. [ 7.997048@3] aml_wifi aml_wifi: [usb_power_control] Set WiFi power down [ 7.997084@3] aml_wifi aml_wifi: [extern_wifi_set_enable] WIFI Disable! 481 [ 8.005646@3] systemd[1]: Started systemd-journald.service. [ 8.076995@1] systemd-journald[418]: Received client request to flush runtime journal. [ 8.317134@0] aml_wifi aml_wifi: [extern_wifi_set_enable] WIFI Enable! 481 [ 8.317154@0] aml_wifi aml_wifi: [usb_power_control] Set WiFi power on ! [ 8.525930@0] meson-gx-mmc fe088000.sdio: 52 [0xc00], TIMEOUT[0x2800] [ 8.526951@0] meson-gx-mmc fe088000.sdio: 52 [0x80000c08], TIMEOUT[0x2800] [ 8.532251@0] meson-gx-mmc fe088000.sdio: 8 [0x1aa], TIMEOUT[0x2800] [ 8.562441@1] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) [ 8.564764@1] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 8.567083@1] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 8.571265@1] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) [ 8.686034@1] Data 1 aligned delay is 0 [ 8.686052@1] mmc2: clk 199999997 div 5 tuning start [ 8.688999@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.689014@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.689020@1] meson_mmc_fixadj_tuning() d1_dly 0, window start 0, size 5 [ 8.689025@1] mmc2: clk 199999997 div 5 tuning start [ 8.692083@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.692100@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.692106@1] meson_mmc_fixadj_tuning() d1_dly 1, window start 0, size 5 [ 8.692111@1] mmc2: clk 199999997 div 5 tuning start [ 8.694932@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.694948@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.694954@1] meson_mmc_fixadj_tuning() d1_dly 2, window start 0, size 5 [ 8.694959@1] mmc2: clk 199999997 div 5 tuning start [ 8.697457@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.697472@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.697477@1] meson_mmc_fixadj_tuning() d1_dly 3, window start 0, size 5 [ 8.697482@1] mmc2: clk 199999997 div 5 tuning start [ 8.700024@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.700037@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.700043@1] meson_mmc_fixadj_tuning() d1_dly 4, window start 0, size 5 [ 8.700048@1] mmc2: clk 199999997 div 5 tuning start [ 8.702516@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.702531@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.702536@1] meson_mmc_fixadj_tuning() d1_dly 5, window start 0, size 5 [ 8.702542@1] mmc2: clk 199999997 div 5 tuning start [ 8.705459@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.705474@1] mmc2: adj_win: < 0 1 2 3 4 > [ 8.705479@1] meson_mmc_fixadj_tuning() d1_dly 6, window start 0, size 5 [ 8.705484@1] mmc2: clk 199999997 div 5 tuning start [ 8.707517@1] mmc2: adj_win: < 0 1 2 3 > [ 8.707532@1] mmc2: adj_win: < 0 1 2 3 > [ 8.707536@1] mmc2: best_s = 0, best_sz = 4 [ 8.707539@1] tuning-c:2, tuning-s:4 [ 8.707544@1] mmc2: clk= 0x10000205, adj = 0x22000, dly1 = 0, dly2 = 0 [ 8.708704@1] mmc2: new ultra high speed SDR104 SDIO card at address 0001 [ 8.708711@0] mmc2: clock 199999997, 4-bit-bus-width [ 8.708711@0] [ 8.709672@0] [sdio_reinit] finish [ 8.709684@0] aml_wifi aml_wifi: [usb_power_control] Set WiFi power on ! [ 9.020976@0] sdio_reset_comm(): [ 9.025827@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 9.026815@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 9.027777@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 9.028741@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 9.028818@0] mmc2: Error resetting SDIO communications (-110) [ 9.028826@0] [sdio_reinit] finish [ 9.028834@0] aml_wifi aml_wifi: [pci_reinit] pci wifi reinit! [ 10.202799@3] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.207928@1] Console: switching to colour dummy device 80x25 [ 10.507612@1] amlvideo2 canvas alloc done fa, fb, fc [ 10.551466@2] amlvideo2.1 cma memory is a8400000 , size is 1800000 [ 10.551803@2] amlvideo2 canvas free fa, fb, fc [ 10.551992@2] amlvideo2.1 cma memory release succeed [ 10.562077@3] amlvideo2 canvas alloc done 20, 21, 22 [ 10.568457@1] ionvid: dbg: vidioc_open [ 10.568457@1] [ 10.568600@1] ionvid: dbg: vidioc_close!!!! [ 10.568600@1] [ 10.568627@0] ionvid: dbg: vidioc_close [ 10.568627@0] [ 10.580371@0] ionvid: dbg: vidioc_open [ 10.580371@0] [ 10.580506@0] ionvid: dbg: vidioc_close!!!! [ 10.580506@0] [ 10.580527@3] ionvid: dbg: vidioc_close [ 10.580527@3] [ 10.582983@3] amlvideo2.0 cma memory is a8400000 , size is 1800000 [ 10.583182@3] amlvideo2 canvas free 20, 21, 22 [ 10.583362@3] amlvideo2.0 cma memory release succeed [ 10.599929@1] ionvid: dbg: vidioc_open [ 10.599929@1] [ 10.600268@1] ionvid: dbg: vidioc_close!!!! [ 10.600268@1] [ 10.600341@3] ionvid: dbg: vidioc_close [ 10.600341@3] [ 10.635637@3] mali fe400000.bifrost: Kernel DDK version r37p0-01eac0 [ 10.636097@3] mali fe400000.bifrost: max pp is 2 [ 10.636110@3] mali fe400000.bifrost: set min pp to default 1 [ 10.636114@3] mali fe400000.bifrost: min pp is 1 [ 10.636119@3] mali fe400000.bifrost: set min clk default to 0 [ 10.636123@3] mali fe400000.bifrost: min clk is 0 [ 10.636153@3] mali fe400000.bifrost: hiu io source 0x0000000019c6225a [ 10.636164@3] mali fe400000.bifrost: aobus base 0x000000004f99fa23 [ 10.636173@3] mali fe400000.bifrost: reset bus 0x000000001e4af8b4 [ 10.636178@3] mali fe400000.bifrost: clk cntl reg = 0x0 [ 10.636182@3] mali fe400000.bifrost: num of pp used most of time 1 [ 10.636187@3] mali fe400000.bifrost: clock dvfs cfg table size is 6 [ 10.636199@3] mali fe400000.bifrost: no reset_cfg [ 10.636205@3] mali fe400000.bifrost: no apb_reset [ 10.636220@3] mali fe400000.bifrost: max clk set 4 [ 10.636224@3] mali fe400000.bifrost: max clk is 4 [ 10.636228@3] mali fe400000.bifrost: turbo clk set to 5 [ 10.636232@3] mali fe400000.bifrost: turbo clk is 5 [ 10.636236@3] mali fe400000.bifrost: default clk set to 4 [ 10.636240@3] mali fe400000.bifrost: default clk is 4 [ 10.636246@3] mali fe400000.bifrost: ====================0==================== [ 10.636246@3] clk_freq= 285714285, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshold=<0 76>, clk_sample=285 [ 10.636251@3] mali fe400000.bifrost: ====================1==================== [ 10.636251@3] clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshold=<80 120>, clk_sample=400 [ 10.636256@3] mali fe400000.bifrost: ====================2==================== [ 10.636256@3] clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshold=<80 120>, clk_sample=500 [ 10.636261@3] mali fe400000.bifrost: ====================3==================== [ 10.636261@3] clk_freq= 666666666, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshold=<80 120>, clk_sample=666 [ 10.636267@3] mali fe400000.bifrost: ====================4==================== [ 10.636267@3] clk_freq= 846000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshold=<80 255>, clk_sample=846 [ 10.636272@3] mali fe400000.bifrost: ====================5==================== [ 10.636272@3] clk_freq= 846000000, clk_parent= gp0_pll, voltage=1150, keep_count=5, threshold=<80 255>, clk_sample=846 [ 10.636276@3] mali fe400000.bifrost: clock dvfs table size is 6 [ 10.636291@3] kernel version >= 5.4 [ 10.657033@3] gpu cooling register okay with err=0 [ 10.657164@3] gpu core cooling register okay with err=0 [ 10.657177@3] mali fe400000.bifrost: kbase_device_runtime_init [ 10.657186@3] mali fe400000.bifrost: pm_callback_runtime_on [ 10.657192@3] mali fe400000.bifrost: pm_runtime_get_sync ret=0 [ 10.657197@3] mali fe400000.bifrost: pm_runtime enabled [ 10.657216@3] mali fe400000.bifrost: shader_present=1, tiler_present=1, l2_present=1 [ 10.657390@3] mali fe400000.bifrost: GPU identified as 0x3 arch 7.0.9 r0p0 status 0 [ 10.657457@3] mali fe400000.bifrost: No priority control manager is configured [ 10.657464@3] mali fe400000.bifrost: No memory group manager is configured [ 10.676410@3] ionvid: dbg: vidioc_open [ 10.676410@3] [ 10.676540@3] ionvid: dbg: vidioc_close!!!! [ 10.676540@3] [ 10.676564@2] ionvid: dbg: vidioc_close [ 10.676564@2] [ 10.677792@2] mali fe400000.bifrost: Probed as mali0 [ 10.682714@0] ionvid: dbg: vidioc_open [ 10.682714@0] [ 10.682874@0] ionvid: dbg: vidioc_close!!!! [ 10.682874@0] [ 10.682940@2] ionvid: dbg: vidioc_close [ 10.682940@2] [ 10.682976@2] ionvid: dbg: vidioc_open [ 10.682976@2] [ 10.683096@0] ionvid: dbg: vidioc_close!!!! [ 10.683096@0] [ 10.687540@3] ionvid: dbg: vidioc_open [ 10.687540@3] [ 10.687546@0] ionvid: dbg: vidioc_open [ 10.687546@0] [ 10.687699@0] ionvid: dbg: vidioc_close!!!! [ 10.687699@0] [ 10.687724@3] ionvid: dbg: vidioc_close [ 10.687724@3] [ 10.687737@3] ionvid: dbg: vidioc_close!!!! [ 10.687737@3] [ 10.687756@3] ionvid: dbg: vidioc_close [ 10.687756@3] [ 10.696211@3] ionvid: dbg: vidioc_open [ 10.696211@3] [ 10.696342@3] ionvid: dbg: vidioc_close!!!! [ 10.696342@3] [ 10.696364@2] ionvid: dbg: vidioc_close [ 10.696364@2] [ 10.705070@3] ionvid: dbg: vidioc_close [ 10.705070@3] [ 10.990542@3] device-mapper: uevent: version 1.0.3 [ 10.990817@3] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 11.079239@3] hdmitx: hdmitx20_ext_get_audio_status[3182] val = 1 [ 11.408271@2] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null) [ 11.656869@1] v4lvid: dbg: v4lvideo open [ 11.676289@2] v4lvid: dbg: v4lvideo open [ 11.676420@2] v4lvid: dbg: vidioc_close!!!! [ 11.678525@1] EXT4-fs (dm-1): mounted filesystem without journal. Opts: (null) [ 11.683447@1] v4lvid: dbg: vidioc_close!!!! [ 11.689945@3] v4lvid: dbg: v4lvideo open [ 11.690086@3] v4lvid: dbg: vidioc_close!!!! [ 11.690975@0] v4lvid: dbg: v4lvideo open [ 11.691113@0] v4lvid: dbg: vidioc_close!!!! [ 11.702133@0] v4lvid: dbg: v4lvideo open [ 11.702255@0] v4lvid: dbg: vidioc_close!!!! [ 11.705115@0] v4lvid: dbg: v4lvideo open [ 11.705241@0] v4lvid: dbg: vidioc_close!!!! [ 11.715341@2] v4lvid: dbg: v4lvideo open [ 11.715467@2] v4lvid: dbg: vidioc_close!!!! [ 11.744872@0] v4lvid: dbg: v4lvideo open [ 11.745524@0] v4lvid: dbg: vidioc_close!!!! [ 11.752661@0] v4lvid: dbg: v4lvideo open [ 11.752786@0] v4lvid: dbg: vidioc_close!!!! [ 11.801554@2] checking watermark status return 0xFFFFFFFF [ 11.801684@2] optee_armtz: initialized driver [ 12.007096@1] [dhd] _dhd_module_init: in Dongle Host Driver, version 101.10.591.33.20 (20230725-3)(gdbe2bd9) [ 12.007096@1] /home/docker/build_dir/CoreELEC-21/build.CoreELEC-Amlogic-ne.aarch64-21/build/ap6xxx-aml-7a64f4c3f0435e56b8e02c7bff0a77f11d650089/bcmdhd.101.10.591.x compiled on Sep 8 2024 at 02:32:42 [ 12.007096@1] [ 12.007132@1] [dhd] ANDROID_VERSION = 11 [ 12.007397@1] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=72, oob_irq_flags=0x8 [ 12.007409@1] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1 [ 12.007416@1] [dhd] dhd_wifi_platform_load: Enter [ 12.007497@1] [dhd] Power-up adapter 'DHD generic adapter' [ 12.007510@1] [dhd] wifi_platform_set_power = 1, delay: 200 msec [ 12.007516@1] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 12.007549@1] aml_wifi aml_wifi: [extern_wifi_set_enable] WIFI Enable! 481 [ 12.213085@3] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec [ 12.213120@3] [dhd] wifi_platform_bus_enumerate device present 1 [ 12.213128@3] [dhd] ======== Card detection to detect SDIO card! ======== [ 12.213137@3] sdio_reset_comm(): [ 12.218546@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 12.219650@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 12.220683@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 12.221795@0] meson-gx-mmc fe088000.sdio: 5 [0x0], TIMEOUT[0x2800] [ 12.224550@2] mmc2: Error resetting SDIO communications (-110) [ 12.224569@2] [sdio_reinit] finish [ 12.225802@2] [dhd] dummy_probe: enter [ 12.226998@2] [dhd] dummy_probe: enter [ 12.243414@2] [dhd] bcmsdh_register: register client driver [ 12.244443@2] [dhd] bcmsdh_sdmmc_probe: Enter num=1 [ 12.245762@2] [dhd] bcmsdh_sdmmc_probe: Enter num=2 [ 12.245776@2] [dhd] bus num (host idx)=2, slot num (rca)=1 [ 12.245782@2] [dhd] found adapter info 'DHD generic adapter' [ 12.245813@2] [dhd] succeed to alloc static buf [ 12.246759@2] [dhd] sdioh_attach: set sd_f2_blocksize 256 [ 12.248986@2] [dhd] sdioh_attach: sd clock rate = 400000 [ 12.264383@2] [dhd] F1 signature read @0x18000000=0x1042aae8 [ 12.319803@3] Bluetooth: bt_init: Core ver 2.22 [ 12.319928@3] NET: Registered protocol family 31 [ 12.402351@1] [dhd] F1 signature OK, socitype:0x1 chip:0xaae8 rev:0x2 pkg:0x4 [ 12.423621@2] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000 [ 12.424752@2] Wifi: bcmdhd_mem_prealloc: [dhd] STATIC-ERROR) bcmdhd_mem_prealloc : request DHD_INFO(42584) > 34816 [ 12.424766@2] [dhd] wifi_platform_prealloc: failed to alloc static mem section 7 [ 12.424849@2] [dhd] dhd_conf_set_chiprev : devid=0xaae8, chip=0xaae8, chiprev=2 [ 12.424859@2] [dhd] dhd_conf_disable_slpauto : dhd_slpauto = 1 [ 12.447019@2] [dhd] dhd_log_dump_init: kernel log buf size = 512KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 76KB [ 12.458182@2] [dhd] dhd_attach(): thread:dhd_watchdog_thread:42c started [ 12.462285@3] [dhd] dhd_attach(): thread:dhd_dpc:42d started [ 12.463494@0] [dhd] dhd_dpc_thread: set dhd_dpc_prio 98 [ 12.466883@0] [dhd] dhd_attach(): thread:dhd_rxf:42e started [ 12.466911@0] [dhd] dhd_deferred_work_init: work queue initialized [ 12.466923@0] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2 [ 12.466927@0] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40 [ 12.467003@0] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3 [ 12.467021@0] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x1070 [ 12.534000@1] meson8b-dwmac fdc00000.ethernet eth0: PHY [0.0:00] driver [YT8531 Gigabit Ethernet] [ 12.545026@1] meson8b-dwmac fdc00000.ethernet eth0: No Safety Features support found [ 12.545052@1] meson8b-dwmac fdc00000.ethernet eth0: PTP not supported by HW [ 12.545063@1] meson8b-dwmac fdc00000.ethernet eth0: configuring for phy/rgmii link mode [ 12.784664@3] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN [ 12.787958@3] [dhd] Dongle Host Driver, version 101.10.591.33.20 (20230725-3)(gdbe2bd9) [ 12.787958@3] /home/docker/build_dir/CoreELEC-21/build.CoreELEC-Amlogic-ne.aarch64-21/build/ap6xxx-aml-7a64f4c3f0435e56b8e02c7bff0a77f11d650089/bcmdhd.101.10.591.x compiled on Sep 8 2024 at 02:32:42 [ 12.787958@3] [ 12.788567@3] [dhd] Register interface [wlan0] MAC: 50:41:1c:2a:c7:9c [ 12.788567@3] [ 12.788655@3] [dhd] [wlan0] wl_android_wifi_off : g_wifi_on=1 force_off=1 [ 12.788676@3] [dhd] dhd_bus_devreset: == Power OFF == [ 12.790131@1] [dhd] dhd_open: WLAN driver is not initialized [ 12.793134@3] [dhd] dhd_bus_stop: making DHD_BUS_DOWN [ 12.793754@3] [dhd] bcmsdh_oob_intr_unregister: Enter [ 12.793782@3] [dhd] bcmsdh_oob_intr_unregister: irq is not registered [ 12.793807@3] [dhd] dhd_bus_devreset: making dhdpub up FALSE [ 12.793822@3] [dhd] dhd_txglom_enable: enable 0 [ 12.793829@3] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN [ 12.794948@3] [dhd] wifi_platform_set_power = 0, delay: 0 msec [ 12.794984@3] [dhd] ======== PULL WL_REG_ON(-1) LOW! ======== [ 12.795026@3] aml_wifi aml_wifi: [extern_wifi_set_enable] WIFI Disable! 481 [ 12.795034@3] [dhd] [wlan0] wl_android_wifi_off : out [ 12.795301@3] [dhd] wl_android_post_init: 0 [ 12.795385@3] [dhd] _dhd_module_init: Exit err=0 [ 12.890173@3] BT_RADIO going: on [ 12.890191@3] AML_BT: going ON,btpower_evt=0 [ 12.890196@3] [off_def_power]: pid: 1102 comm: rfkill [ 13.096986@1] [on_def_power]: pid: 1102 comm: rfkill [ 13.820984@1] [dhd] [wlan0] dhd_open : Enter [ 13.821002@1] [dhd] Dongle Host Driver, version 101.10.591.33.20 (20230725-3)(gdbe2bd9) [ 13.821002@1] /home/docker/build_dir/CoreELEC-21/build.CoreELEC-Amlogic-ne.aarch64-21/build/ap6xxx-aml-7a64f4c3f0435e56b8e02c7bff0a77f11d650089/bcmdhd.101.10.591.x compiled on Sep 8 2024 at 02:32:42 [ 13.821002@1] [ 13.821019@1] [dhd] dhd_open: ######### called for ifidx=0 ######### [ 13.821035@1] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0 [ 13.821041@1] [dhd] wifi_platform_set_power = 1, delay: 200 msec [ 13.821048@1] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 13.821072@1] aml_wifi aml_wifi: [extern_wifi_set_enable] WIFI Enable! 481 [ 14.021839@3] Bluetooth: hci_uart_init: HCI UART driver ver 2.3 [ 14.021857@3] Bluetooth: hci_uart_register_proto: HCI UART protocol H4 registered [ 14.021861@3] Bluetooth: hci_uart_register_proto: HCI UART protocol BCSP registered [ 14.021933@3] Bluetooth: hci_uart_register_proto: HCI UART protocol LL registered [ 14.021938@3] Bluetooth: hci_uart_register_proto: HCI UART protocol ATH3K registered [ 14.021961@3] Bluetooth: hci_uart_register_proto: HCI UART protocol Three-wire (H5) registered [ 14.022223@3] Bluetooth: hci_uart_register_proto: HCI UART protocol Intel registered [ 14.022364@3] Bluetooth: hci_uart_register_proto: HCI UART protocol Broadcom registered [ 14.022387@3] Bluetooth: hci_uart_register_proto: HCI UART protocol QCA registered [ 14.022391@3] Bluetooth: hci_uart_register_proto: HCI UART protocol AG6XX registered [ 14.022412@3] Bluetooth: hci_uart_register_proto: HCI UART protocol Marvell registered [ 14.029009@1] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec [ 14.029035@1] [dhd] sdio_sw_reset: call mmc_sw_reset [ 14.029996@0] meson-gx-mmc fe088000.sdio: 52 [0xc00], TIMEOUT[0x2800] [ 14.031042@0] meson-gx-mmc fe088000.sdio: 52 [0x80000c08], TIMEOUT[0x2800] [ 14.036478@0] meson-gx-mmc fe088000.sdio: 52 [0xc00], TIMEOUT[0x2800] [ 14.037456@0] meson-gx-mmc fe088000.sdio: 52 [0x80000c08], TIMEOUT[0x2800] [ 14.042722@0] meson-gx-mmc fe088000.sdio: 8 [0x1aa], TIMEOUT[0x2800] [ 14.075100@1] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) [ 14.077693@3] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 14.080610@0] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) [ 14.084667@1] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) [ 14.193154@3] Data 1 aligned delay is 0 [ 14.193171@3] mmc2: clk 199999997 div 5 tuning start [ 14.196115@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.196137@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.196145@3] meson_mmc_fixadj_tuning() d1_dly 0, window start 0, size 5 [ 14.196152@3] mmc2: clk 199999997 div 5 tuning start [ 14.198797@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.198808@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.198812@3] meson_mmc_fixadj_tuning() d1_dly 1, window start 0, size 5 [ 14.198817@3] mmc2: clk 199999997 div 5 tuning start [ 14.201511@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.201518@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.201522@3] meson_mmc_fixadj_tuning() d1_dly 2, window start 0, size 5 [ 14.201526@3] mmc2: clk 199999997 div 5 tuning start [ 14.204095@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.204100@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.204104@3] meson_mmc_fixadj_tuning() d1_dly 3, window start 0, size 5 [ 14.204108@3] mmc2: clk 199999997 div 5 tuning start [ 14.206705@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.206711@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.206715@3] meson_mmc_fixadj_tuning() d1_dly 4, window start 0, size 5 [ 14.206719@3] mmc2: clk 199999997 div 5 tuning start [ 14.209329@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.209334@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.209338@3] meson_mmc_fixadj_tuning() d1_dly 5, window start 0, size 5 [ 14.209342@3] mmc2: clk 199999997 div 5 tuning start [ 14.212206@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.212222@3] mmc2: adj_win: < 0 1 2 3 4 > [ 14.212228@3] meson_mmc_fixadj_tuning() d1_dly 6, window start 0, size 5 [ 14.212233@3] mmc2: clk 199999997 div 5 tuning start [ 14.214559@3] mmc2: adj_win: < 0 1 2 3 > [ 14.214569@3] mmc2: adj_win: < 0 1 2 3 > [ 14.214573@3] mmc2: best_s = 0, best_sz = 4 [ 14.214577@3] tuning-c:2, tuning-s:4 [ 14.214582@3] mmc2: clk= 0x10000205, adj = 0x22000, dly1 = 0, dly2 = 0 [ 14.214626@3] [dhd] sdioh_start: set sd_f2_blocksize 256 [ 14.214810@3] [dhd] dhd_bus_devreset: == Power ON == [ 14.214877@3] [dhd] F1 signature read @0x18000000=0x1042aae8 [ 14.217315@3] [dhd] F1 signature OK, socitype:0x1 chip:0xaae8 rev:0x2 pkg:0x4 [ 14.217808@3] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000 [ 14.217850@3] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN [ 14.217882@3] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN [ 14.217981@3] [dhd] dhd_conf_disable_slpauto : dhd_slpauto = 1 [ 14.218062@3] [dhd] dhd_os_open_image1: /usr/lib/firmware/brcm/config.txt (507 bytes) open success [ 14.237511@1] [dhd] dhd_conf_read_country : ccode = SG [ 14.237538@1] [dhd] dhd_conf_read_others : bcn_timeout = 20 [ 14.237551@1] [dhd] dhd_conf_read_pm_params : PM = 0 [ 14.237589@1] [dhd] dhd_conf_read_nv_by_chip : nv_by_chip_count=16 [ 14.237594@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xa962, chiprev=0, name=nvram_ap6181.txt [ 14.237598@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xa962, chiprev=1, name=nvram_ap6210.txt [ 14.237602@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt [ 14.237606@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt [ 14.237610@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xa9a6, chiprev=2, name=nvram_ap6236.txt [ 14.237613@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4345, chiprev=6, name=nvram_ap6255.txt [ 14.237617@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4345, chiprev=9, name=nvram_ap6256.txt [ 14.237621@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4330, chiprev=4, name=nvram_ap6330.txt [ 14.237625@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4339, chiprev=1, name=nvram_ap6335.txt [ 14.237629@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4354, chiprev=1, name=nvram_ap6354.txt [ 14.237632@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4354, chiprev=2, name=nvram_ap6356.txt [ 14.237636@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4335, chiprev=1, name=nvram_bcm4335.txt [ 14.237640@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xa94c, chiprev=2, name=nvram_ap6234.txt [ 14.237644@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4359, chiprev=9, name=nvram_ap6359s.txt [ 14.237648@1] [dhd] dhd_conf_read_nv_by_chip : chip=0x4334, chiprev=3, name=nvram_bcm4334.txt [ 14.237652@1] [dhd] dhd_conf_read_nv_by_chip : chip=0xaae8, chiprev=2, name=nvram_ap6275s.txt [ 14.237666@1] [dhd] dhd_conf_set_path_params : Final fw_path=/usr/lib/firmware/brcm/fw_bcm43752a2_ag.bin [ 14.237670@1] [dhd] dhd_conf_set_path_params : Final nv_path=/usr/lib/firmware/brcm/nvram_ap6275s.txt [ 14.237673@1] [dhd] dhd_conf_set_path_params : Final clm_path=/usr/lib/firmware/brcm/clm_bcm43752a2_ag.blob [ 14.237677@1] [dhd] dhd_conf_set_path_params : Final conf_path=/usr/lib/firmware/brcm/config.txt [ 14.238161@3] [dhd] dhd_os_open_image1: /usr/lib/firmware/brcm/fw_bcm43752a2_ag.bin (685923 bytes) open success [ 14.246163@3] [dhd] dhd_os_open_image1: /usr/lib/firmware/brcm/fw_bcm43752a2_ag.bin (685923 bytes) open success [ 14.246184@3] [dhd] dhdsdio_download_code_file Using SINGLE image (size 685923) [ 14.308765@3] [dhd] dhd_os_open_image1: /usr/lib/firmware/brcm/nvram_ap6275s.txt (8361 bytes) open success [ 14.317958@3] [dhd] # AP6275S_NVRAM_V1.2.1_20200311 [ 14.318575@3] [dhd] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 14.378365@3] [dhd] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 14.378601@3] [dhd] bcmsdh_oob_intr_register: HW_OOB irq=72 flags=0x8 [ 14.378663@3] [dhd] bcmsdh_oob_intr_register: disable_irq_wake [ 14.378761@3] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3 [ 14.379314@0] [dhd] dhd_dpc_thread: set dhd_dpc_prio 98 [ 14.381612@3] [dhd] wlc_ver_major 12, wlc_ver_minor 1 [ 14.381623@3] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1 [ 14.381626@3] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40 [ 14.382788@3] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address 50:41:1c:2a:c7:9c [ 14.382867@3] [dhd] dhd_os_open_image1: /usr/lib/firmware/brcm/clm_bcm43752a2_ag.blob (28865 bytes) open success [ 14.383303@3] [dhd] dhd_check_current_clm_data: ----- This FW is not included CLM data ----- [ 14.399907@3] [dhd] dhd_apply_default_clm: CLM download succeeded [ 14.400426@3] [dhd] dhd_check_current_clm_data: ----- This FW is included CLM data ----- [ 14.402377@3] [dhd] Firmware up: op_mode=0x0005, MAC=50:41:1c:2a:c7:9c [ 14.402762@3] [dhd] Disable tdls_auto_op failed. -1 [ 14.405179@3] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 26 ret: 0 [ 14.407848@3] [dhd] arp_enable:1 arp_ol:0 [ 14.411947@3] [dhd] Driver: 101.10.591.33.20 (20230725-3) [ 14.411947@3] [dhd] Firmware: wl0: Dec 4 2019 01:55:28 version 18.35.387.11 (wlan=r853831) FWID 01-ae9dfd3b [ 14.411947@3] [dhd] CLM: 9.9.5_SS (2019-12-04 01:26:12) [ 14.412197@3] [dhd] dhd_txglom_enable: enable 1 [ 14.412215@3] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy [ 14.412219@3] [dhd] dhd_conf_set_txglom_params : txglomsize=36, deferred_tx_len=0 [ 14.412223@3] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128, dhd_txminmax=-1 [ 14.412227@3] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0, txctl_tmo_fix=300 [ 14.412239@3] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1, disable_proptx=-1 [ 14.414107@3] [dhd] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64 [ 14.415661@3] [dhd] dhd_pno_init: Support Android Location Service [ 14.416261@3] [dhd] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23 [ 14.416269@3] [dhd] dhd_rtt_init : FTM is not supported [ 14.416274@3] [dhd] dhd_rtt_init EXIT, err = 0 [ 14.431613@3] [dhd] dhd_ecounter_autoconfig Ecounter autoconfig in fw failed : 0 [ 14.431774@3] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed [ 14.457545@0] [dhd] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created (WLC_E_ALLOW_CREDIT_BORROW) [ 14.459199@3] [dhd] dhd_conf_set_country : set country SG, revision 0 [ 14.464032@3] [dhd] dhd_conf_set_country : Country code: SG (SG/0) [ 14.470936@3] [dhd] CONFIG-ERROR) dhd_conf_set_intiovar : txack_alive setting failed -23 [ 14.471432@3] [dhd] [wlan0] wl_android_wifi_on : Success [ 14.503553@3] [dhd] CFG80211-ERROR) __wl_update_wiphybands : error get bw_cap 6g (-13) [ 14.536036@3] [dhd] [wlan0] wl_cfg80211_up : Roam channel cache enabled [ 14.537798@3] [dhd] [wlan0] dhd_open : Exit ret=0 [ 14.537811@3] [dhd] [wlan0] dhd_pri_open : tx queue started [ 14.642057@3] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0 [ 16.639363@1] meson8b-dwmac fdc00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 16.639404@1] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.649029@0] 8021q: 802.1Q VLAN Support v1.8 [ 16.924998@3] [TEE] E/TA: MM-module-name:Video firmware TA,Version:1.0.5-g3604ffd(build:1624) [ 16.925015@3] [TEE] E/TA: fw_check_pack_version:292 the package has 17 fws totally. [ 16.925019@3] [TEE] E/TA: fw_check_pack_version:309 The TA ver is v1.0 [ 16.925022@3] [TEE] E/TA: fw_check_pack_version:310 The fw ver is v0.4 [ 16.925025@3] [TEE] E/TA: fw_data_insert:389 the fw with 384 KB will be loaded. [ 16.925028@3] [TEE] M/TA: TEE_Video_Load_FW success [ 17.357263@0] dovi: no symbol version for module_layout [ 17.357285@0] dovi: module license 'AML' taints kernel. [ 17.357289@0] Disabling lock debugging due to kernel taint [ 17.359354@0] *** amlogic_dolby_vision_init dv: sc2 *** [ 17.359381@0] *** register_dv_stb_functions.*** [ 17.359404@0] hdr10_policy 115, ko_info SHENZHEN SDMC TECHNOLOGY CO LTD chip_name = sc2 [stb:2.4:e]-[v1.0]-[ Mon 13 Feb 2023 02:08:07 PM CST]-[ jialong.jiang]-[* stb_2.4]-[1fecf8d96bae61ce5e1043c53050083cd34c4559]-[Date: Mon Nov 14 10:54:07 2022 +0000]-[0] [ 17.359409@0] efuse_mode=0 reg_value = 0x18 [ 17.359413@0] dv capability 7 [ 17.359981@0] hdmitx: hdmitx_set_vsif_pkt: type=0, tunnel_mode=0, signal_sdr=0 [ 17.359996@0] hdmitx: hdmitx: Dolby VSIF, VEN_DB2[3]) = 0 [ 17.443427@0] hdmitx: hdmitx_set_vsif_pkt: type=0, tunnel_mode=0, signal_sdr=1 [ 17.443461@0] hdmitx: hdmitx: Dolby VSIF, VEN_DB2[3]) = 0 [ 17.443475@0] hdmitx: hdmitx: Dolby VSIF, switching signal to SDR [ 17.443496@0] hdmitx: vic:16, cd:6, cs:1, cr:1 [ 17.467508@3] No find node. [ 17.467527@3] get dos device failed, id 50(0), try to search dos device data [ 17.467532@3] dos_device_search_data, get major 28 dos dev data success [ 17.467536@3] dos init chip 50(0), device info : [ 17.467539@3] max_vdec_clock : 800 MHz [ 17.467542@3] max_hevcf_clock : 800 MHz [ 17.467545@3] max_hevcb_clock : 800 MHz [ 17.467548@3] hw_esparser_support : no [ 17.467551@3] vdec_canvas_support : no [ 17.467554@3] initial_dos_device end [ 17.467562@3] register clk_set_setting cpu[50] [ 17.469111@3] Registered firmware driver success. [ 17.470277@3] Try to load video/h264_enc.bin ... [ 17.470421@3] firmware_codec firmware_vdec: Direct firmware load for video/h264_enc.bin failed with error -2 [ 17.470433@3] Error : -2 can't load the video/h264_enc.bin. [ 17.470437@3] get data from fsys fail. [ 17.470441@3] invalid file type. [ 17.470786@3] Try to load video/video_ucode.bin ... [ 17.471680@3] load firmware size : 440384, Name : video/video_ucode.bin. [ 17.472876@3] parse_ucode_version, ucode = 0.4.55 [ 17.535718@1] power domain: name: pwrc-vdec, dev: ffffffb11445a400, link: ffffffb114b0a800 [ 17.539205@1] power domain: name: pwrc-hcodec, dev: ffffffb11445a800, link: ffffffb11494e000 [ 17.539230@1] vdec vdec: Get pwrc-vdec-2 failed, pm-domain: 0 [ 17.542586@1] power domain: name: pwrc-hevc, dev: ffffffb11445ac00, link: ffffffb11b6ba000 [ 17.542629@1] vdec vdec: Get pwrc-hevcb failed, pm-domain: 0 [ 17.542635@1] vdec vdec: Get pwrc-wave failed, pm-domain: 0 [ 17.542640@1] vdec power init success! [ 17.553182@0] Amlogic A/V streaming port init [ 17.567784@3] no need to register_tync_func. [ 17.567797@3] no need to register_tync_func. [ 17.567800@3] no need to register_tync_func. [ 17.567803@3] no need to register_tync_func. [ 17.567806@3] no need to register_tync_func. [ 17.567808@3] no need to register_tync_func. [ 17.567811@3] no need to register_tync_func. [ 17.567813@3] no need to register_tync_func. [ 17.567816@3] no need to register_tync_func. [ 17.567836@3] get gate demux control failed 0000000000000000 [ 17.567841@3] get gate parser_top control failed 0000000000000000 [ 17.567856@3] get gate vdec control ok ffffffb11cdc1900 [ 17.567861@3] get gate clk_81 control failed 0000000000000000 [ 17.567868@3] get gate clk_vdec_mux control ok ffffffb11cdc1800 [ 17.567875@3] get gate clk_hcodec_mux control ok ffffffb11cdc1700 [ 17.567879@3] get gate clk_hevc_mux control failed 0000000000000000 [ 17.567886@3] get gate clk_hevcb_mux control ok ffffffb11cdc1600 [ 17.567891@3] get gate ahbarb0 control failed 0000000000000000 [ 17.567896@3] get gate asyncfifo control failed 0000000000000000 [ 17.567903@3] get gate clk_hevcf_mux control ok ffffffb11cdc1500 [ 17.567908@3] get mux clk err. [ 17.567910@3] get mux clk err. [ 17.567913@3] get mux clk err. [ 17.567916@3] get mux clk err. [ 17.567919@3] get mux clk err. [ 17.567921@3] get mux clk err. [ 17.606694@3] v4l dec module init [ 17.607673@3] aml-vcodec-dec vcodec_dec: v4ldec registered as /dev/video26 [ 17.620971@1] [0]: vcodec_dec decoder ffffffb11707c000 [ 17.621142@1] [0]: release decoder ffffffb11707c000 [ 17.621210@1] [0]: v4ldec has been destroyed. [ 17.629196@3] amvdec_avs module init [ 17.752058@3] amvdec_avs3_driver_init_module bufspec_index = 2 [ 17.838524@0] amvdec_h264 module init [ 17.872622@3] ammvdec_h264 module init [ 17.889841@3] amvdec_h265 module init [ 17.936474@3] ammvdec_mpeg12 module init [ 17.953675@1] ammvdec_mpeg4_driver_init_module [ 17.968050@1] amvdec_vc1 module init [ 17.989874@3] amvdec_av1 module init [ 18.005906@1] amvdec_vp9 module init [ 18.030761@1] amvdec_vp9 module init [ 18.053173@1] amvdec_h265 module init [ 18.068552@1] amvdec_av1 module init [ 18.256064@2] Registered IR keymap rc-empty [ 18.256189@2] rc rc0: meson-ir as /devices/platform/fe084040.meson-ir/rc/rc0 [ 18.257339@2] rc rc0: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter [ 18.257473@2] input: meson-ir as /devices/platform/fe084040.meson-ir/rc/rc0/input9 [ 18.260197@0] meson-ir fe084040.meson-ir: receiver initialized [ 18.384987@3] rc rc0: two consecutive events of type space [ 18.388557@3] IR NEC protocol handler initialized [ 18.419945@1] IR RC6 protocol handler initialized [ 18.485749@1] input: eventlircd as /devices/virtual/input/input10 [ 21.732132@0] Not init audio effects [ 21.732343@0] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:tdm@1 [ 21.733701@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:tdm@1 [ 21.748051@0] Not init audio effects [ 21.748283@0] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:tdm@1 [ 21.749984@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:tdm@1 [ 21.750794@0] Not init audio effects [ 21.750998@0] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:i2s2hdmi [ 21.751911@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:i2s2hdmi [ 21.752904@0] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:spdif@0 [ 21.753510@0] spdif_a keep clk continuous [ 21.753519@0] spdif_a keep clk continuous [ 21.753631@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:spdif@0 [ 21.754743@0] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:spdif@1 [ 21.755809@0] spdif_b keep clk continuous [ 21.755818@0] spdif_b keep clk continuous [ 21.755930@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:spdif@1 [ 21.767173@3] Not init audio effects [ 21.767375@3] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:i2s2hdmi [ 21.768747@3] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 21.768910@3] notify tdm to hdmitx,id 2 codec_type 0 [ 21.768964@3] hdmitx: hw: set audio [ 21.768970@3] hdmitx: hw: hdmitx audio_param->channel_num = 1, hdev->aud_output_ch = 33 [ 21.768986@3] hdmitx: fs = 3, cd = 6, tmds_clk = 148500 [ 21.768991@3] hdmitx: hw: aud_n_para = 6144 [ 21.769001@3] hdmitx: hw: set channel status [ 21.796936@3] hdmitx: hw: [0x10e3] = 0x1f [ 21.796971@3] hdmitx: audio: Audio Type: PCM [ 21.796981@3] iec_info: rate: 44100, codec_type:0x0, channel status L:0x100, R:0x100 [ 21.796987@3] hdmitx: hdmitx_notify_callback_a[6391] type:0 rate:44100 size:32 chs:2 fifo_rst:0 aud_src_if:1 [ 21.796991@3] hdmitx: hw: set audio [ 21.796995@3] hdmitx: hw: hdmitx audio_param->channel_num = 1, hdev->aud_output_ch = 33 [ 21.797008@3] hdmitx: fs = 2, cd = 6, tmds_clk = 148500 [ 21.797012@3] hdmitx: hw: aud_n_para = 6272 [ 21.797022@3] hdmitx: hw: set channel status [ 21.824933@3] hdmitx: hw: [0x10e3] = 0x1f [ 21.824966@3] hdmitx: audio: Audio Type: PCM [ 21.824971@3] hdmitx: audio: set audio param [ 21.825065@2] aml_T9015_audio_set_bias_level [ 21.825117@1] aml_T9015_audio_set_bias_level [ 21.825306@1] notify tdm to hdmitx,id 2 codec_type 0 [ 21.825318@1] iec_info: rate: 44100, codec_type:0x0, channel status L:0x100, R:0x100 [ 21.825325@1] hdmitx: hdmitx_notify_callback_a[6391] type:0 rate:44100 size:32 chs:2 fifo_rst:0 aud_src_if:1 [ 22.674662@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 22.675779@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 22.676860@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 22.830342@3] cec: CEC framework ctrl enabled [ 23.106040@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.107144@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.108225@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.356456@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.357542@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.358607@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.607265@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.608371@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.609474@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.807855@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.808976@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 23.810067@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 25.022423@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 25.023487@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 25.024521@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 27.002804@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 27.004077@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 27.005121@0] meson-gx-mmc fe088000.sdio: 52 [0x92003e01], TIMEOUT[0x2800] [ 27.011264@1] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, bssidx: 0 [ 33.117578@0] input: Télécommande Keyboard as /devices/virtual/misc/uhid/0005:00C4:0080.0003/input/input11 [ 33.118127@0] input: Télécommande Consumer Control as /devices/virtual/misc/uhid/0005:00C4:0080.0003/input/input13 [ 33.118325@0] input: Télécommande Mouse as /devices/virtual/misc/uhid/0005:00C4:0080.0003/input/input14 [ 33.118569@0] input: Télécommande as /devices/virtual/misc/uhid/0005:00C4:0080.0003/input/input15 [ 33.118778@0] hid-generic 0005:00C4:0080.0003: input,hidraw2: BLUETOOTH HID v0.01 Keyboard [Télécommande] on 50:41:1c:2a:c7:9d [ 54.012323@1] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2, bssidx: 0 [ 109.729750@0] audio_ddr_mngr: frddr stop success, fifo id 0, regbase:0x70, arb sts:0x40000010 [ 109.729860@0] notify tdm to hdmitx,id 2 codec_type 0 [ 109.729870@0] iec_info: rate: 44100, codec_type:0x0, channel status L:0x100, R:0x100 [ 109.729878@0] hdmitx: hdmitx_notify_callback_a[6391] type:0 rate:44100 size:32 chs:2 fifo_rst:0 aud_src_if:1 [ 119.730216@0] aml_tdm_hw_setting_free(), disable mclk for tdm-2 [ 119.730449@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:i2s2hdmi [ 119.730533@0] aml_T9015_audio_set_bias_level [ 119.730562@0] aml_T9015_audio_set_bias_level [ 135.077568@1] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3, bssidx: 0 [ 204.831200@0] hdmitx: system: irq 4 0 [ 204.831230@0] hdmitx: UTC+0 2024-09-08 02:22:22 HPD LOW [ 204.831288@0] hdmitx: system: plugout [ 204.831325@0] hdmitx: hdmitx: Dolby VSIF, VEN_DB2[3]) = 0 [ 204.831335@0] hdmitx: hdmitx: Dolby VSIF, switching signal to SDR [ 204.831341@0] hdmitx: vic:16, cd:6, cs:1, cr:1 [ 204.831352@0] hdmitx: hdmitx_set_hdr10plus_pkt: null vsif [ 204.831381@0] [RX]-up_phy_addr = 0 [ 204.831386@0] hdmitx: system: update physical size: 16 9 [ 204.831481@0] [drm] drm hdmitx hpd notify [ 204.831486@0] [drm] meson_hdmitx_hpd_cb[1998] [ 378.032139@1] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 4, bssidx: 0 [ 465.533855@0] hdmitx: system: irq 2 0 [ 465.533885@0] hdmitx: UTC+0 2024-09-08 02:26:43 HPD HIGH [ 466.044945@0] hdmitx: system: plugin [ 466.175510@0] hdmitx: edid: EDID Parser: [ 466.175535@0] [RX]-up_phy_addr = 4 [ 466.175541@0] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 466.175546@0] hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=0 [ 466.175549@0] hdmitx: Edid_ParsingVendSpec:ieeeoui=0xd046,len=11 [ 466.175553@0] hdmitx: v2 VSVDB: len=11, sup_2160p60hz=1, Interface=0 [ 466.175564@0] hdmitx: edid: get dtd0 vic: 4 [ 466.175580@0] hdmitx: edid: get dtd1 vic: 97 [ 466.175583@0] hdmitx: edid: get dtd2 vic: 16 [ 466.175586@0] hdmitx: edid: change preferred_mode from 4 to 97 [ 466.175590@0] hdmitx: hdmitx: get PMT vic: 97 [ 466.175594@0] hdmitx: edid: find IEEEOUT [ 466.175598@0] hdmitx: edid: check sum valid [ 466.175601@0] hdmitx: edid: check sum valid [ 466.175611@0] hdmitx: edid: check sum valid [ 466.175614@0] hdmitx: edid: check sum valid [ 466.175621@0] hdmitx: edid: blk0 raw data [ 466.175641@0] hdmitx: edid: [ 466.175641@0] 00ffffffffffff004dd904aa01010101011e0103807a44780a0dc9a057479827 [ 466.175641@0] 12484c2108008180a9c0714fb300010101010101010108e80030f2705a80b058 [ 466.175641@0] 8a00c2ad4200001e023a801871382d40582c4500c2ad4200001e000000fc0053 [ 466.175641@0] 4f4e5920545620202a30300a000000fd0017790e883c000a2020202020200178 [ 466.175641@0] [ 466.175641@0] [ 466.175646@0] hdmitx: edid: blk1 raw data [ 466.175666@0] hdmitx: edid: [ 466.175666@0] 020364f05861605d5e5f621f101405130420223c3e1203110265663f402f0d7f [ 466.175666@0] 071507503d07bc570601670403830f00006e030c004000b83c2b008001020304 [ 466.175666@0] 67d85dc401788003eb0146d00044038888627697e200cbe305df01e40f030030 [ 466.175666@0] e3060d01011d007251d01e206e285500c2ad4200001e00000000000000000034 [ 466.175666@0] [ 466.175666@0] [ 466.175670@0] hdmitx: system: update physical size: 1220 680 [ 466.175676@0] hdmitx: system: get current mode: 1080p60hz [ 466.175679@0] hdmitx: system: update physical size: 1220 680 [ 466.175702@0] hdmitx: hdmitx: display colourdepth is forced by attr to 12 bits (VIC: 16) [ 466.175723@0] hdmitx: video: already init VIC = 0 Now VIC = 16 [ 466.176747@0] hdmitx: hw: div40: 0 [ 466.203218@0] hdmitx: frac_rate = 0 [ 466.203233@0] hdmitx: config HPLL = 5940000 frac_rate = 0 [ 466.203307@0] hdmitx: config HPLL done [ 466.203317@0] hdmitx: set_hpll_od3_clk_div[467] div = 6 [ 466.203324@0] hdmitx: j = 4 vid_clk_div = 1 [ 466.203407@0] hdmitx: set enc for VIC: 16 [ 466.203423@0] hdmitx: hw: config hdmitx IP vic = 16 cd:6 cs: 1 [ 466.216563@0] hdmitx: adjust decouple fifo [ 466.252944@0] hdmitx: video: Sink is HDMI device [ 466.252992@0] hdmitx: hw: set audio [ 466.252996@0] hdmitx: hw: hdmitx audio_param->channel_num = 1, hdev->aud_output_ch = 33 [ 466.253010@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148500 [ 466.253015@0] hdmitx: hw: aud_n_para = 6272 [ 466.253025@0] hdmitx: hw: set channel status [ 466.280945@0] hdmitx: hw: [0x10e3] = 0x1f [ 466.280984@0] hdmitx: audio: Audio Type: PCM [ 466.280992@0] hdmitx: hw: set audio [ 466.280996@0] hdmitx: hw: hdmitx audio_param->channel_num = 1, hdev->aud_output_ch = 33 [ 466.281010@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148500 [ 466.281014@0] hdmitx: hw: aud_n_para = 6272 [ 466.281024@0] hdmitx: hw: set channel status [ 466.308953@0] hdmitx: hw: [0x10e3] = 0x1f [ 466.308993@0] hdmitx: audio: Audio Type: PCM [ 466.309121@0] [drm] drm hdmitx hpd notify [ 466.309131@0] [drm] meson_hdmitx_hpd_cb[1993] [ 493.278770@2] Not init audio effects [ 493.279033@2] audio_ddr_mngr: frddrs[0] registered by device fe330000.audiobus:i2s2hdmi [ 493.280638@2] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3) [ 493.280780@2] notify tdm to hdmitx,id 2 codec_type 0 [ 493.280794@2] iec_info: rate: 44100, codec_type:0x0, channel status L:0x100, R:0x100 [ 493.280802@2] hdmitx: hdmitx_notify_callback_a[6391] type:0 rate:44100 size:32 chs:2 fifo_rst:0 aud_src_if:1 [ 493.280884@2] aml_T9015_audio_set_bias_level [ 493.280965@0] aml_T9015_audio_set_bias_level [ 493.281225@1] notify tdm to hdmitx,id 2 codec_type 0 [ 493.281237@1] iec_info: rate: 44100, codec_type:0x0, channel status L:0x100, R:0x100 [ 493.281245@1] hdmitx: hdmitx_notify_callback_a[6391] type:0 rate:44100 size:32 chs:2 fifo_rst:0 aud_src_if:1 [ 605.620505@0] hdmitx: system: irq 4 0 [ 605.620532@0] hdmitx: UTC+0 2024-09-08 02:29:03 HPD LOW [ 605.620580@0] hdmitx: system: plugout [ 605.620600@0] hdmitx: hdmitx: Dolby VSIF, VEN_DB2[3]) = 0 [ 605.620610@0] hdmitx: hdmitx: Dolby VSIF, switching signal to SDR [ 605.620624@0] hdmitx: vic:16, cd:6, cs:1, cr:1 [ 605.620634@0] hdmitx: hdmitx_set_hdr10plus_pkt: null vsif [ 605.620662@0] [RX]-up_phy_addr = 0 [ 605.620668@0] hdmitx: system: update physical size: 16 9 [ 605.620756@0] [drm] drm hdmitx hpd notify [ 605.620761@0] [drm] meson_hdmitx_hpd_cb[1998] [ 625.186313@0] audio_ddr_mngr: frddr stop success, fifo id 0, regbase:0x70, arb sts:0x40000010 [ 625.186415@0] notify tdm to hdmitx,id 2 codec_type 0 [ 625.186425@0] iec_info: rate: 44100, codec_type:0x0, channel status L:0x100, R:0x100 [ 625.186433@0] hdmitx: hdmitx_notify_callback_a[6391] type:0 rate:44100 size:32 chs:2 fifo_rst:0 aud_src_if:1 [ 635.186666@0] aml_tdm_hw_setting_free(), disable mclk for tdm-2 [ 635.186803@0] audio_ddr_mngr: frddrs[0] released by device fe330000.audiobus:i2s2hdmi [ 635.186888@0] aml_T9015_audio_set_bias_level [ 635.186917@0] aml_T9015_audio_set_bias_level [ 678.106528@1] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 5, bssidx: 0 [ 978.051815@1] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 6, bssidx: 0